纖維貼面塊 的英文怎麼說

中文拼音 [xiānwéitiēmiànkuāi]
纖維貼面塊 英文
veneering modules
  • 纖 : 纖形容詞（細小） fine; minute
  • 維 : Ⅰ動詞1 （連接） tie up; hold together; link 2 （保持; 保全） maintain; safeguard; preserve; keep ...
  • 貼 : Ⅰ動詞1 （粘貼） stick; paste; glue 2 （緊挨） nestle up to; snuggle up to 3 （貼補） subsidize; h...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 纖維 : fibre; staple; filamentary
  1. This paper introduces that the diffuse heat heating furnace is reduced the consumption of fuel is debased and the preferable effect is got, using the multicrystal mullite fibrous stickup lump to heat preservation in heating furnace wall

    摘要採用多晶莫來石纖維貼面塊對加熱爐爐內壁保溫，減少了爐體的散熱損失，降低了爐子燃耗，取得了較好的效果。
  2. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
分享友人
分享到 Line

分享到臉書