纖維面層板 的英文怎麼說

中文拼音 [xiānwéimiàncéngbǎn]
纖維面層板 英文
fiber covered plywood
  • 纖 : 纖形容詞（細小） fine; minute
  • 維 : Ⅰ動詞1 （連接） tie up; hold together; link 2 （保持; 保全） maintain; safeguard; preserve; keep ...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 纖維 : fibre; staple; filamentary
  1. To improve the binding strength between the deck slabs and deck surfacing layer of badong changjiang river highway bridge and to provide the surfacing layer with anti - cracking ductility, a series of technical measures has been taken in the construction of the deck surfacing of the bridge, including those of embedding binding reinforcement in the deck slabs, spraying inorganic binding agent between the slabs and layer, replacing part of the cement with micro expansion agent and adding appropriate amount of polypropylene fibers to the concrete

    摘要巴東長江公路大橋橋面鋪裝，通過採取預埋橋面粘接鋼筋、噴塗無機界面粘結劑、用微膨脹劑替代部分水泥、在混凝土中摻入適量的聚丙烯纖維等措施來提高橋面板與鋪裝層間的界面粘結強度和給橋面抗裂增韌。
  2. The coupling agent presumably improves the bond between the glass surface and the resin matrix in a laminate.

    偶聯劑的作用是設想能改善層壓板中纖維表面與樹脂基體的粘結。
  3. According to the feature that deformation resulted from water absorption and mildew appear mainly on the rabbet surface of ccf, this paper adopts rsst to spray a special waterproof sealant on rabbet surface of ccf, so that the sealant can get into fiberboard to certain extent by means of capillarity and penetration, blockage the holes between fibers and capillary, cut up passage of water and change the properties of soakage and sorption to water in capillarity and fiber. at the same time, solidified sealant can form a compact waterproof pellicle on rabbet surface so as to prevent water and humidity from fiber ' s expansion and mildewing

    針對吸水變形、霉變主要發生在地板企口表面的特徵，採用企口表面全封閉法，在復合強化地板企口表面噴塗特殊的防水封閉劑，使其依靠毛細管作用及滲透作用進入板內一定深度，堵塞木纖維之間的空隙及毛細孔通道，截斷水分傳遞的渠道，並改變毛細孔壁及纖維的表面性質以不利於水的浸潤與吸附，同時其固化后能在企口表面形成一層緻密的憎水薄膜，防止水分、濕氣從企口侵入板內引起木纖維膨脹變形、發霉等現象。
  4. In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer

    本文針對武漢軍山長江公路大橋鋼箱梁橋面鋪裝工程，從鋪裝層環境溫度變化范圍、交通量等使用條件出發，在用algorfeas有限元分析軟體分析鋪裝層受力變形基礎上，提出了（即鋼板+金屬鋅塗層+封閉層+粘接劑+預拌瀝青碎石+雙層sma ）的高性能鋼橋面sma鋪裝體系，並對這種sma的組成材料，包括改性瀝青、集料、礦粉、纖維進行了比較研究，設計了這種sma的配合比，對sma混合料的性能進行了對比試驗，對這種sma方案進行了疲勞性能研究，驗證了所選擇sma方案的可行性。
  5. Three - dimensionally braided structural composites have distinct structure that is fully integrated, continuously spatial fiber - network impregnated with ductile material. the new innovative materials have not plies as conventional composites have, and put an end once and all to low interlaminar strength showing in laminate materials. because of their enhanced stiffness and strength in the thickness direction, near - net - shape design and manufacturing, superior damage tolerance and specified aerospace function, the braided composites are gaining more and more attention of industry and academia

    三維編織結構復合材料是完全整體、連續、多向的紡線（纖維束）的網路，充填以延性材料，這類新材料已失去通常復合材料的層合板概念，由此，層合板復合材料層間脆弱的致命弱點在編織結構復合材料中得到克服，所以編織結構復合材料具有高的強度和剛度（包括在厚度方向） ，接近實際形狀的製造，高的沖擊韌性、高的損傷阻抗，和按實際設計要求的特定的航空航天方面的使用功能，因而廣泛地受到工業界和學術界的關注。
  6. To fuel further growth and profits, in tandem with an expansion plan in the pipeline, the group has been engineering steps to achieve notable sales of epoxy resin to outside parties in the near future

    環氧樹脂不單是生產環氧玻璃纖維覆銅面板的主要原料，此化工產品亦被廣泛應用於半導體包裝接合劑塗層絕緣及建築行業。
  7. Installation of sheet roof and wall coverings - profiled fibre cement - code of practice

    薄板屋面和墻面塗敷層.成形纖維水泥.實施規程
  8. With the material dynamic constitutive equation including damage and the effect of stain rate the predictable formula about ballistic limit velocity of fiber composite target. secondly based on the damage feature about ceramic / fiber composite target caused by impact load, analysis model about defense performance of ceramic / composite material target is formed and the predictable formula about ballistic limit velocity is also given. lastly using the reflection and projectile theory of stress wave the paper discusses the design of ceramic / composite material target, optimizes the design of double layer ceramic / composite targets, gains optimal coefficient under certain area density and discusses the variety relationship of area density and thickness with optimal coefficient u nder some ballistic limit velocity 3

    首先，分析了纖維類正交鋪層復合靶板在沖擊載荷作用下的損傷破壞機理，結合包含損傷和應變率效應的材料動態本構方程，建立了纖維復合材料板彈道極限速度的預測公式；其次，根據陶瓷/纖維材料復合靶板在沖擊載荷下的破壞特點，建立了陶瓷/復合材料靶板抗彈性能分析模型，給出了彈道極限速度預測公式；最後，利用應力波反射和透射理論討論了陶瓷/復合材料靶板的設計問題，對雙層陶瓷復合靶板的優化設計進行了分析，給出了在一定面密度下的最佳優化系數，討論了一定彈道極限速度下的面密度和厚度隨優化系數的變化關系。
  9. ( 4 ) according to the principle of " repair as the old ", the schemes of foundation strengthening, the schemes of the body structure, the schemes of the shear wall strengthening, the schemes of the floor strengthening, the schemes of the brace layout, the schemes of the switch floor construction and special strengthening scheme such as carbon fiber, the wall steel wire grid strengthening are achieved in this paper

    按照「修舊如舊」的原則實現了照舊色做舊，使新舊構件的色澤差別諧調。依據上述原則，論文實現了基礎加固施工方案，主體結構加固施工方案、剪力墻加固施工方案、樓板拆除支撐和砼施工方案、支撐布置方案、高層主體結構轉換層施工方案、木屋蓋拆除方案以及特殊加固工程施工技術如粘鋼加固、碳纖維布加固、墻面鋼絲網加固等。
  10. In order to overcome the scarcity of tensility, toughness and durability of layer steel fiber reinforced concrete ( lsfrc ), layer - hybrid - fibers - reinforced - concrete ( lhfrc ) is offered. much less steel fibers are evenly distributed on the surface and the bottom about 10mm of the pavement slabs, the middle body of which is composed of polypropylene fiber concrete

    為了解決層布式鋼纖維混凝土所存在的延性、韌性、耐久性不足，我們提出了層布式混雜纖維混凝土路面，它是將一定體積率的鋼纖維均勻撒佈於路面板距上下表面大約10mm的層面內，其中間部分為聚丙烯纖維混凝土。
  11. Under the mutual action of fatigue and creep, the destroy form of the composite board is mainly the syntheses of the fiber fracture, interface destroy and interbedded crack

    在疲勞蠕變交互作用下層合板的破壞形式主要為纖維撕裂、界面剪切破壞和層間開裂3種形式的綜合表現。
  12. The in - plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and it ' s found that the in - plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5 %. the tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space. the

    研究結果表明：隨著縫紉密度、縫紉線直徑、最大纖維偏轉角和縫紉變形區寬度的增加，縫紉復合材料層合板面內等效模量逐漸降低，最大降幅一般在5 %左右；縫紉復合材料層合板的拉伸強度隨縫紉針距的增加而增大，隨縫紉行距的增加而降低，因此縫紉密度對拉伸強度的影響程度要看具體的縫紉針距和行距。
  13. . 3 base materials for printed circuits ; part 2 : specifications ; specification 9 : epoxide cellulose paper core, epoxide glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test ; amendment 3

    印製電路用基材.第2部分:規范.第9號規范:易燃的具有環氧纖維紙芯且表面覆銅的環氧玻璃布層壓板
  14. Illustrated by a tensile composite plate with an open hole and a pin - loaded hole, fiber placement path planning of the fully - steered ply is studied. the optimization of fiber placement paths for composite plate - parts is studied, two kinds of algorithm are brought out to meet different requirements of base - line - path

    3 .將層合板的加強層纖維鋪放路徑優化方法推廣應用於曲面板類復合材料構件的纖維鋪放軌跡規劃，並根據不同基準鋪放路徑數目提出了兩種纖維鋪放軌跡密化演算法。
  15. Epoxy - bonding a carbon - fiber composite plate to the tension face of concrete beam is an effective technique for repair and retrofit of concrete beams. in the first part of this paper, based on the fracture mechanics and the theory of beam, a theoretic model is proposed to analyze the shear stress in the adhesive between carbon - fiber composite and concrete. and then the closure - form solution for the shear stress distribution is drawn

    本文的第一部分基於斷裂力學與梁的基本理論，對碳纖維加固混凝土梁的粘結膠層以及粘結界面的剪應力分佈進行了理論分析，得出了其理論解析解；討論了碳纖維板的粘結長度、粘結厚度和粘結膠層的抗剪模量對界面剪應力分佈的影響。
  16. The following principles are proved : increasing cfp adhesive length will release the concentrating of shear stress near the cutoff point, this will lead to the increment of loading - bear capacity of concrete beams ; increasing the thickness of cfp will improve the transition of load from concrete beam to cfp, this is useful to exert the potential of cfp ; in creasing the anti - shear modulus of adhesive will result enhance the concentrating of shear stress, this is harmful to the effect of cfp reinforced concrete beams

    本文的理論分析結果可以表明：增加碳纖維板的粘結長度可以緩解碳纖維板端部界面上的剪應力集中，改善混凝土梁結構的加固效果；增大碳纖維板的粘結厚度可以增大界面上的剪應力，改善混凝土樑上載荷向碳纖維板的傳遞效果，有利於充分發揮碳纖維布的潛能；如果粘結膠層的抗剪模量過大會加劇剪應力的集中，從而對碳纖維加固的效果不利。
  17. It can be concluded that the performance differences between the plate membrane and the hollow fiber membrane can be attribute to difference of the stresses in the membranes when they were under pressure and the difference of the strain caused in the membrane, besides the possible reason that the surface curvature difference between a plate substrate and a hollow fiber one may cause structure difference in the dense functional layer when coating. the stresses in a hollow fiber composite membrane under an outside pressure are quite different from that in a plate one in that they exert on the hollow fiber in both the radial and circular directions, and the compress strain of the hollow fiber is thus much more complex, which may cause the top layer crinkle and a decreased salt rejection

    分析認為造成平板復合膜（ ）和中空纖維復合膜（ ）性能差異的主要原因，除了平板基膜與中空纖維基膜因表面曲率不同可能引起在塗覆時形成的緻密功能層結構上的差異之外，由於中空纖維膜受外壓時，膜內部承受的應力形式與平板膜不同，會同時在徑向（膜厚度方向）和環向（膜面內方向）兩個方向產生壓應力，因此，所發生的形變也較為復雜，可能造成表面復合層的起皺或脫落，引起脫鹽率下降。
  18. The results show that, for flexural - tensile fatigue test and shear fatigue test, the two kinds of structure of common asphalt concrete with strata stress absorbed layer and glass fiber grating had good ability to resist reflection cracking, while the effect of paving asphalt concrete directly on cement concrete slab was worse

    結果表明，對于彎拉型疲勞試驗和剪切型疲勞試驗，普通瀝青混凝土下面鋪設strata應力吸收層、玻璃纖維格柵2種結構都具有良好的抗反射裂縫的能力，而在水泥混凝土面板上直接加鋪瀝青混凝土類結構的效果最差。
  19. Standard specification for asphalt - coated glass fiber base sheet used in roofing

    屋面用瀝青覆層的玻璃纖維基薄板的標準規范
  20. Thermal conductivity of honeycomb sandwich panels with carbon fibre mesh plates at low temperature

    網狀碳纖維面板蜂窩夾層結構低溫熱導率測試研究
分享友人
分享到 Line

分享到臉書