聯機量熱計 的英文怎麼說
中文拼音 [liánjīliángrèjì]
聯機量熱計
英文
on-line calorimeter-
The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality
而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。By means of c - language, the paper has developed a large - scale computer program, in which the combination of both the newton iteration and the gradient method is introduced to solve reynolds equation and film thickness equation, and the march method is used to solve the energy equation and heat interface equations, the satisfactory results are obtained
本文採用c語言編制了大型計算機程序進行數值計算，數值計算中採用梯度-牛頓聯合法求解reynolds方程和油膜厚度方程，採用步進法求解能量方程和熱界面方程，獲得了滿意的數值結果。Through the research of crosslinking of matrix resin, heating treatment of composite and mixing of different polymer, we draw some conclusions : 1 、 percolation theory can explain the phenomenon of the jump of resistance when the content of cb reach a critical volume ; 2 、 based on ohm conduct theory, abounded to the percolation the wbibull statistical theory and other theory, an adapted theory was obtained to explain the jump of resistance and the other phenomenon ; 3 、 the ntc phenomenon was eliminated by crosslinking the matrix of conductive composite, at the same time the stability of composite was improved
通過對基體樹脂的交聯、復合材料的熱處理、聚合物共混物的研究得出了如下的結論： 1 、滲濾理論能夠很好的解釋導電粒子含量達到某一值時電導率劇增的問題； 2 、在歐姆導電模型的基礎上，綜合應用了weibull統計理論模型，結合原來的體積膨脹等理論，成功的解釋了ptc復合材料在基體材料熔點附近的跳變問題、 ntc現象以及熱循環穩定性等問題； 3 、有機ptc導電復合材料經硅烷交聯以後能夠消除ntc現象，改善了導電復合材料的穩定性能。This paper analyses current situation of chp and situation of development, use evaluating energy utilization - - based on electricity comparing with state calculated method - - based on heat, calculates the operating data of baotou second thermal power plant heat supply system ， extends the study of heat supply performance to heat net and heat consumer, synthetically analyses heat load characteristic 、 pipe net property and heat supply distance witch effect heat supply cost. the paper studies the thermal power performance of thermal power plant total energy system, discuss heat supply cost which effect the development of chp
本文對熱電聯產的現狀及發展情況進行分析，採用能源利用系統性能評價指標體系及其評價指標? ?電量法與國家目前採用的法定計量方法? ?熱量法進行比較，通過對內蒙古包頭第二熱電廠供熱熱源系統及供熱熱網系統的熱電聯產運行數據進行分析計算，將供熱過程的熱力性能研究延伸至熱網和熱用戶，分析用戶終端的能源利用情況，針對內蒙古地區主力機組和地區條件，綜合分析了熱負荷特性、管網性能及供熱距離對供熱成本的影響，研究了熱電廠總能系統的熱力性能，對困擾熱電聯產的供熱成本進行了探討。So a reforming design scheme of the cogeneration of heat and power project is put forward to change fuel from natural gas into coal in the basis of using original equipment
目前，受海上能源供應限制，供氣量明顯不足，致使孤北熱電廠燃氣機組閑置，從油田實際出發，以孤北熱電廠現存設備為設計依據，將原機組改為燃煤熱電聯產形式。The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved
本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。On - line monitoring of hvcb is the precondition of predicting maintenance, is the key element of reliable run, and is the important supplement to the traditional off - line preventive maintenance in fact, the faults are made by hvcb, no matter in number or in times, is over 60 % of total faults so it has determinative importance for improving the reliability of power supply and this can greatly decrease the capital waste used by - dating overhaul in this paper, the inspecting way of hvcb mechanism characteristic is discussed the concept of sub - circuit protector is presented, the scheme that we offered has been combined with sub - circuit integrality monitoring theory, to ensure that it has the two functions as a whole according the shut - off times at rated short circuit given by hvcb manufacturer, the electricity longevity loss can be calculated in each operation, and the remained longevity can be forecast too an indirect way for calculating main touch ' s temperature by using breaker shell temperature, air circumference temperature and breaker ' s heat resistance is improved in this paper, and main touch resistance can be calculated if providing the load current msp430, a new single chip microcomputer made by ti company, is engaged to develop the hardware system of the on - line monitoring device, and special problem brought by the lower supply voltage range of this chip is considered fully
高壓斷路器所造成的事故無論是在次數，還是在事故所造成的停電時間上都占據總量60以上。因此，及時了解斷路器的工作狀態對提高供電可靠性有決定性意義；並可以大大減少盲目定期檢修帶來的資金浪費。本文論述了斷路器機械特性參數監測方法；提出了二次迴路保護器的概念，並將跳、合閘線圈完整性監視和二次迴路保護結合起來，給出具有完整性監視功能的二次迴路保護器實現方案；根據斷路器生產廠家提供的斷路器額定短路電流分斷次數，計算每次分閘對應的觸頭電壽命損耗，預測觸頭電壽命；提出根據斷路器殼體溫度和斷路器周圍空氣溫度結合斷路器熱阻來計算斷路器主觸頭穩態溫升的方法，並根據此時的負荷電流間接計算主觸頭迴路的電阻；在硬體電路設計上，採用美國ti公司最新推出的一種功能強大的單片機msp430 ，並充分考慮該晶元的適用電壓范圍給設計帶來的特殊問題；在通信模塊的設計中，解決了不同工作電壓晶元之間的介面問題，並給出了直接聯接的接線方案。The algorithm of strapdown inertial navigation system is also discussed and then use the flight - track generator to give a simulation, since a closed loop feedback integrated navigation system is designed in this paper, and the output of the filter must feed back to the strapdown inertial navigation system, the analysis of the algorithm in strapdown inertial navigation system is important. the scheme to design the trajectory of gps and the simulation of gps constellation are then studied, the simulation of gps constellation is given from the calculation of vernal equinox base on the principle of celestial mechanics, this method of different from other methods given by other paper and is useful to the research of satellite navigation system. a new method to abstract noise modal in integrated navigation system is proved to be useful in practice, this method, which is given by use the principles of stochastic processes, statistics, time series analysis, and system identification, is suitable for the kalman filter in integrated navigation system
如航跡產生器的設計，該航跡產生器是研究組合導航問題的前提，從國外一些研究組合導航系統的文獻中可以看出，設計這樣一個航跡產生器是非常必要的，所以本文自行設計了這樣一個系統；還討論了捷聯慣性導航系統中捷聯解算的方法，並進行了模擬研究，由於在本文設計的閉環反饋式組合導航系統中，對捷聯慣導系統的平臺誤差進行閉環控制，需要將濾波器輸出的校正量反饋到捷聯解算內部，所以必須對捷聯解算進行深入的研究和分析，更何況捷聯解算問題本身也是導航界的一個熱門研究課題；另外，本文還介紹了gps軌道及其星座模擬的設計思想和方案，與以往gps軌道和星座模擬不同的是本文從天體力學中計算春分點開始，逐步進行gps軌道及其星座模擬，這樣的設計方法對從事衛星導航的研究工作是有價值的；還對組合導航中誤差建模方法進行了研究，綜合運用隨機過程、概率統計、時序分析及系統辯識等方面的理論提出了一套適合組合導航卡爾曼濾波的誤差建模方法，並運用實際研究工作中的測量數據對該方法進行了驗證。Abstract : a thermo - economical diagnostic mathematical model for pressurizedwater reactor ( pwr ) nuclear cogeneration plant is proposed based on heat assignment method. this model simplifies the calculation of thermal system and can be used to calculate the index variations caused by heating steam parameters as temperature, return percentage and return place of the return water. some examples are given to show the usefulness of this model
文摘:基於熱電聯產機組熱量法分配的特點，建立了熱電聯產壓水堆機組熱力系統發生變化對熱經濟性指標影響的計算模型，提出了供熱系統參數? ?供熱回水率、回水溫度、回水地點變化對壓水堆機組熱經濟性影響的定量診斷數學模型，可將復雜的熱力系統全面計算簡化成3個一次方程.通過實例計算，驗證了所提數學模型是正確可行的，同時具有概念清晰、計算簡捷的特點Based on the experiments, the simulation of the heat exchanger and scroll compressor was accomplished which also offered a favorable condition to the establishment of the whole gwshp methods were used to improve the veracity and astringency of the model, such as : dividing the condenser into several tiny segment with equal area ; separating the condensing process into single - phase region and double - phase region ; the comparing result showed that most of the error between the data of simulation and experiment was within 5 % while the maximal error was 8. 35 %
在建模過程中，從大量蒸發和冷凝的換熱關聯式中，通過與實驗數據的比較找出了與實驗結果最為接近的換熱關聯式在建模過程中，針對冷凝器及板式換熱器的特點，採取將冷凝器按面積分成若干個微元段，並將冷凝過程分成單相區和兩相區的方法。同時對渦旋壓縮機進行建模和分析同時在熱力學平衡基礎上與實驗數據比較，經過驗證，對于換熱器模型，模擬計算與實驗結果的誤差一般都在5以內，最大為12 。The key points of this paper include the design of software and hardware of the system, and the realization of automatic control function. the monitoring and controlling system adopts a total distributed control system ( dcs ) constituted by a programmable logic controller ( plc ). a computer ( pc ) and thermal power engineering signal sensors, sender, controller, etc
本項研究中採用可編程式控制制器（ plc ）作下位機、工業控制計算機（ pc ）作上位機與熱工參數測量傳感器、變送器、操作控制器等組成集散型控制系統（ dcs ） ，自動監測三聯產試驗臺的各運行參數，並對試驗臺實行自動控制與調節。The third one describes the properties of working fluid and some experiments on viscous - temperature curves of silicone oil, named as 0. 017m2 / s, 0. 027m2 / s and 0. 037m2 / s. the experimental results demonstrate that the dimension of plate and properties of working fluid have influences on life - span and torque transfer performance of lvc. in chapter four, the strength of each component of lvc were designed and corrected and the new seals were used and the space between the inner and outer plate is 0. 4mm
第一章主要說明了課題研究的背景和意義、液體粘性聯軸器的工作原理及其在工程上的應用，介紹了常時四輪驅動汽車的概念與分類；第二章在閱讀大量文獻的基礎上，對液體粘性聯軸器的研究成果進行總結，包括粘性聯軸器的扭矩計算，扭矩輸出所受的影響因素，駝峰發生的機理、駝峰觸發的溫度、駝峰發生時的最小轉速差，聯軸器在發生駝峰現象之前硅油剪切的內部溫度特性，聯軸器的傳熱模型以及汽車速度、滑移率對轉速差的影響。This course provides mechanical engineering students with an awareness of various responses exhibited by solid engineering materials when subjected to mechanical and thermal loadings ; an introduction to the physical mechanisms associated with design - limiting behavior of engineering materials, especially stiffness, strength, toughness, and durability ; an understanding of basic mechanical properties of engineering materials, testing procedures used to quantify these properties, and ways in which these properties characterize material response ; quantitative skills to deal with materials - limiting problems in engineering design ; and a basis for materials selection in mechanical design
本課程向機械工程學系學生提供以下知識：當固態工程材料承受機械或熱載荷時的各種反應；介紹與工程材料之設計極限相關聯的物理機制，特別是剛度、強度、韌性、以及延展性；理解工程材料之基本力學性能；用來量化這些性能的測試手段；以及描述材料反應之特性的方式；定量處理工程設計時所遭遇到材料極限問題；以及機械設計時選擇選擇材料之基本概念。分享友人