胺浸法 的英文怎麼說
中文拼音 [ànjìnfǎ]
胺浸法
英文
amine leaching-
The present work indicates the organic nf membranes and the inorganic nf membranes all have shortages, so develop composite nf membranes that have low cost, mechanically strong and thermally / chemically - resistant, easy to cleanout and good performances is a very important task. in this paper, the preparation of inorganic - organic composite nf membranes were presented. this composite comprise a porous sio2 / al2o3 support substrate, the pore diameters of which ranging from 10 to 15 nm, this inorganic support substrate having a polymer membrane which comprises an polyvinyl alcohol ( pva ) or polyamide ( pa ) densely deposited on at least one of the face surfaces thereof, the structural porosity of such pva and pa membrane ranging from 3 to 5 nm
本論文以開發無機?有機復合納濾膜為出發點，首先在al _ 2o _ 3多孔微濾膜上利用溶膠?凝膠法制備sio _ 2 al _ 2o _ 3無機復合超濾膜作為無機?有機復合納濾膜的基膜；選用聚乙烯醇和聚酰胺為表面功能層材料，分別探討了以羥基丁二酸和磺基水楊酸為混合交聯劑，採用浸塗法制備了聚乙烯醇sio _ 2 ? al _ 2o _ 3復合納濾膜；以均苯二甲酰氯、哌嗪和二胺為單體，採用界面聚合法制備了聚酰胺sio _ 2 ? al _ 2o _ 3復合納濾膜，並對影響膜性能的諸多因素進行系統研究。In this paper, the al3 + - doped zno thin films were prepared on na - ca - si glass substrate ( microscope slides ) by sol - gel process from 2 - methoxyethanol solution prepared by zinc acetate as premonitor, monoethanolamine as stabilizator and aluminum chloride reaction. homogenous, transparent, polycrystalline zno thin film was formed finally by diping coating conducted for film - plate on substrate, drying, pre - heat - treatment, anealing
所用的溶膠是以乙二醇甲醚為溶劑，醋酸鋅為前驅體，乙醇胺為穩定劑反應制得，用浸漬提拉法在基體上鍍膜，經烘烤、預燒、退火，最後形成均勻、透明的多晶zno薄膜。The development in the adhesion between the polymer cords such as rayon, nylon, polyester, and aramid, to rubbers were reviewed from aspects of adhesion test and analysis, fiber and adhesives interface, dipped cord and rubber interface and the mechanical properties of resorcinol formaldehyde latex adhesives
摘要從測試與分析方法、纖維與粘合劑的界面粘合、浸膠簾線與橡膠的粘合、間苯二酚甲醛膠乳浸膠層的物理機械性能等方面總結了人造絲、尼龍、聚酯和芳香聚酰胺等聚合物簾線與橡膠的粘合方法及最新進展。Based on polymerization reaction of the nylon - 6 rubberized cord fabric production of distributed control system in yangzhou organic chemical plant computer integrated manufacturing system ( yh - cims / dcs ), the multiple stepwise regression method was used to build the statistic mathematical models of the molecule weight and the monomer quantum of casting slice belt. then the optimization model of polymerization reaction was presented, which was solved by using simulation annealing algorithm to obtain the best techniques parameters. the improved hybrid genetic algorithm and back propagation algorithm are combined to train neural network, brought out the neural network prediction model of casting slice belt ' s average molecule weight to guide the technologist on - line
提出了流程工業生產過程操作優化策略和應用實施方法，包括生產過程離線優化策略、非線性問題求解策略、在線優化模型及學習策略；結合揚州有機化工廠計算機集成製造系統集散控制系統（ yh - cims dcs ）的實施，針對錦綸? 6浸膠南京理工大學博士學位論文摘要簾于布生產中己內酚胺聚合反應過程優化控制這一工程實際問題，採用統計建模方法，建立了聚合反應過程的優化模型；為求解所得的優化模型，提出了種改進的有約束條件下的模擬退火演算法，該演算法能避免陷於局部最優解，有效地提高了所求解的全局性和可靠性：提出了基於改進的ga演算法和sp演算法相結合的混合學習演算法，建立了基於神經網路的聚合反應過程生產目標在線預測模型，該演算法和模型滿足了生產中的實時性和實用性要求。The surficial modification based on the free radical and the polar which was initiated by radiation. and we proceed to study the preradiation and coradiation grafting and surfacial grafting on the uhmwpe fiber under the electron beam. the grafting monomer were aa, am, st, mma. then we applied grafting ratios sem, ft - ir, dynamic wetting to represent the result of grafting
本文分別採取預輻照和共輻照接枝方法進行了纖維輻照接枝丙烯酸、丙烯酰胺、苯乙烯、甲基丙烯酸甲酯的研究，並運用測算接枝率、 sem 、紅外光譜以及纖維浸潤性測試等方法對接枝效果進行了表徵，並據此分析了影響表面接枝效果的主要因素。Air pollution. nitrogen dioxide content of atmospheric air. method of determination by collection on a triethanolamine - impregnated filter
空氣污染.大氣中二氧化氮含量的測定.用三乙醇胺浸漬的過濾器收集取樣的測定方法分享友人