腐蝕因數 的英文怎麼說

中文拼音 [fǔshíyīnshǔ]
腐蝕因數 英文
corrosion factor
  • 腐 : Ⅰ名詞（豆腐） bean curdⅡ動詞（腐爛; 變壞） decay Ⅲ形容詞（腐爛） rotten; corroded; putrid
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 因 : Ⅰ動詞[書面語] （沿襲） follow; carry on Ⅱ介詞1 [書面語] （憑借; 根據） on the basis of; in accord...
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 腐蝕 : 1 （通過化學作用使物體逐漸消損破壞） corrode; corrosion; corroding; deep etch; diabrosis; rot; ea...
  1. The power ' s level can be no more than the creature ' s hit dice + 2 ( thus, a 1 - hd psionic creature might possess the 3rd - level power fly but not the 4th - level power dissolving touch )

    異能等級不能超過角色的生命骰數+ 2 （因此，一個生命骰1的角色可以擁有3級異能飛行術，但不能擁有4級異能腐蝕之觸） 。
  2. Effects of diamond particles and their adding contents on the coating hardness, friction coefficient, wear resistance, corrosion current density and microstructures were studied

    研究了金剛石粒子及其添加量對塗層硬度、摩擦因數、耐磨性能、腐蝕電流密度和微觀組織的影響。
  3. Through the investigation research on practical damaged element, considering the effect of corrosion, high temperature, wet environment, damage ( crack ) on structural durability, bearing capacity. this paper established the reliability analysis method of large - scale industrial factory, and applied the fuzzy mathematics to establish the factor set and weight coefficient set on the basis of expert experience. an analyzed method for fuzzy evaluation of structural element and bent frame structure system reliability is put forward

    通過對實際結構破損構件的調查，考慮腐蝕，高溫，環境潮濕，破損（裂縫）等因素對結構耐久性、承載力的影響，論文建立了大型工業廠房可靠度的計算方法，利用專家經驗和模糊數學方法建立了模糊評價的因素集和權重集，對鋼筋砼結構構件和廠房排架結構體系進行了模糊評價。
  4. The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack

    摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。
  5. On the basis of the theory of reinforcement corrosion caused by chloride, a chloride diffusion model considering the time - dependent quantities of diffusion coefficient and surface chloride concentration for predicting the content of chloride in concrete is presented in this paper, at the same time, the determination of model factors are analyzed

    論文以氯離子對混凝土結構的侵蝕機理為基礎，在不同氯腐蝕環境下，建立了考慮氯離子擴散系數的時間依賴性及其它因素影響的改進氯離子擴散模型，並對模型參數的選取和確定進行了深入討論。
  6. At present, we use rubber as the material of the diaphragm. it is low life - time because of its poor corrosion resistance

    目前我國大多數隔膜採用的是橡膠材料，這種材料耐腐蝕性差，因此使貯箱的使用壽命受到很大影響。
  7. In addition to maintaining the original natural graphite with characteristics, texture also has soft, flexible, high and low temperature resistance, corrosion resistance, high - dose irradiated milk, and low friction coefficient, which has a wide adaptability

    除保持天然石墨原來具有的特性外，還具有質地柔軟，富有彈性，耐高低溫、耐腐蝕、耐高劑量輻照、摩擦系數低等優點，因而具有廣泛的適應性。
  8. Aluminium titanate ( al2tio5, at ) has many excellent properties such as low thermal expansion coefficient, thermal conduction coefficient, high melting point, endured corrosion and thermal resistance, so it is one of the best materials with low thermal expansion coefficient resisting high temperature

    鈦酸鋁（ al _ 2tio _ 5簡稱at ）因其具有接近於零的熱膨脹系數、低的導熱系數、高熔點、耐腐蝕和抗熱沖擊性能好等特點，是目前低熱膨脹材料中耐高溫性能最好的材料之一。
  9. Flow meters may be affected, giving incorrect reading. the rate of corrosion of pipeline may also increase. the abnormal current induced in power grids may damage transformers because of overheating

    流量計可能會受到干擾，使數據失誤管道的腐蝕速度亦可能會增快電力網路上的不正常電流可能使變壓器因過熱而燒毀。
  10. And it is indicated that the corrosion residual life of the pressure vessel and pipeline shouldn ' t be calculated with normal distribution model since the coefficients of variation of maximal corrosion depth and corrosion rate are often more than 0. 2

    最後指出最大腐蝕深度和腐蝕速率等參數的變異系數往往大於0 . 2 ，因此不宜用正態分佈模型進行壓力容器與管道耐腐蝕剩餘壽命的計算與分析。
分享友人
分享到 Line

分享到臉書