腐蝕裂紋 的英文怎麼說

中文拼音 [fǔshílièwén]
腐蝕裂紋 英文
cc
  • 腐 : Ⅰ名詞（豆腐） bean curdⅡ動詞（腐爛; 變壞） decay Ⅲ形容詞（腐爛） rotten; corroded; putrid
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  • 腐蝕 : 1 （通過化學作用使物體逐漸消損破壞） corrode; corrosion; corroding; deep etch; diabrosis; rot; ea...
  1. Standard test method for evaluating stress - corrosion cracking of stainless alloys with different nickel content in boiling acidified sodium chloride solution

    沸騰酸化氯化鈉溶液中不同鎳合量不銹鋼合金應力腐蝕裂紋評定的標準試驗方法
  2. One reasonable explanation is that etching removes and blunts microcracks.

    有一種合理的解釋是說腐蝕能夠去掉並鈍化微裂紋。
  3. Many studies in the related area of stress corrosion or subcritical crack growth use simplified test systems.

    許多有關應力腐蝕或亞臨界裂紋發展領域的研究使用了簡化的試驗系統。
  4. Furthermore, the supposition of galvanic couple is drawn into the procedure of corrosion fatigue crack growth of aluminum alloys, the relation of couple current vs loading time is determined with electrochemical methods. a formula in the theory is deduced which expresses the stress corrosion crack growth rate of lc4cs aluminum alloy, the results of mathematical modeling preferably correspond with examination

    再將「耦合作用」的猜想，引入鋁合金的腐蝕疲勞裂紋擴展過程中，用電化學的方法測定耦合電流與加載時間的關系，並從理論上導出lc4cs鋁合金應力腐蝕裂紋擴展速率的數學表達式，數學模擬的結果與實驗值具有較好的一致性。
  5. This paper mainly aims at the strategic demands for large - aperture lightweight mirror proposed by high - tech development. its main research contents are : select material blank for lightweight mirror according to physical and chemical properties of optical glass ; analyze and calculate the deformation quantity of the mirror with finite element method ; design and optimize mirror body structure of 400 lightweight plane mirror and 450 lightweight spherical mirror, analyze glass cutting principle, design specisl - use grinding wheel structure, select reasonable technological parameters to implement the processing of weight reduction holes on 400 plane mirror ; analyze etching mechanism of hydrofluoric acid, look for the technological parameters such as the optimal acid concentration and etching time etc. ; eliminate the stress of weight reduction holes and micro - cracks on 400 lightweight plane mirror ; discuss the processing principle and

    本論文的研究主要是瞄準國家高技術對大口徑輕型鏡的戰略需求而開展的。主要研究內容是：根據光學玻璃的物理與化學性能，選擇輕型鏡坯材料；用有限元法對鏡子的變形進行分析、計算，找出變形規律，優化設計400mm輕型平面鏡、 450mm輕型球面鏡鏡體結構；分析玻璃切削原理，設計專用磨輪結構，選擇合理工藝技術參數，完成400mm平面鏡輕量化減重孔的加工；分析氫氟酸腐蝕光學玻璃機理，尋找最佳酸濃度、腐蝕作用時間等工藝參數，實現400mm平面鏡減重孔應力與微裂紋的消除；討論分離器加工原理和工藝技術特點，完成400mm平面輕型鏡面形加工。
  6. Aerospace - space product assurance - material selection for controlling stress - corrosion cracking ; german and english version en 14101 : 2001

    航空航天.航天產品保證.控制應力腐蝕裂紋材料的選擇
  7. Approximate calculation of crack propagation rate of metal corrosion fatigue

    金屬腐蝕疲勞裂紋擴展速率的近似計算
  8. Corrosion of metals ; testing the resistance of metallic materials to stress corrosion cracking ; general

    金屬的腐蝕.金屬材料耐應力腐蝕裂紋性能的檢驗.概況
  9. The above device can be also applied to monitor and measure the crack length in high - or low temperatures and corrosive environment. the aforementioned fcp equation is objectively checked by reanalysis of some existing fcp test data given in available literature

    該系統還可用於高溫或腐蝕環境下的裂紋實時監測，為高溫材料及腐蝕環境下的壽命研究提供了可靠的關鍵技術和測試手段。
  10. Not a timely manner to facilitate the dissolution of auto parts fault detection, vulnerability directly on the surface of metal parts nondestructive testing of the fatigue crack, stress corrosion, crack, crack, etc. folded through " sound ", " light " emergency instructions crack site to the maintenance staff promptly eliminate hidden dangers and guarantee the exercise of automotive safety

    及時方便不解體檢測汽車部件故障，直接對易損金屬部件表面進行無損檢測，對出現的疲勞裂紋，應力腐蝕、裂紋、折疊裂紋等、通過「聲」 、 「光」報警指示裂紋的部位，以使維修人員及時排除隱患，保證汽車安全行使。
  11. The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack

    摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。
  12. According to these, the paper put forward some countermeasures : select low carbon steel or low metal alloy steel with lower intensity, like 20r steel ; while welding, adopt strict craft measures with lower welding heat to input ; after jointing, proceed the whole hot dissolving on time ; control each welding joint with hardness hb 185 ; add 0. 25 % water into the liquid ammonia as decay eclipse ; enhance checking in operation, repairing equipment in time through regular interior and exterior checking

    針對上述原因提出了防止氨冷器類臨氨壓力容器產生應力腐蝕裂紋的對策：選用強度稍低，但抗裂性較好的低碳鋼和低合金鋼，如用20r鋼製造；焊接時應採用嚴格的工藝措施和較低的焊接熱輸入量；焊后應及時進行整體消除應力熱處理；控制焊接接頭各區硬度hb 185 ；在液氨中添加0 . 25 %的水作為緩蝕劑；在運行中加強檢查，及時進行停車檢修時的內外部檢查和定期檢驗。
  13. By the analyses of corrosive medium and manufacturing process quality, the cracks of glycol evaporators in dushanzi petrochemical company have been confirmed to be intergranular corrosion cracks

    摘要通過裂紋宏微觀形貌分析、腐蝕介質分析、對蒸發塔製造過程質量分析等，證實了獨山子石化乙二醇蒸發塔的裂紋屬晶間型應力腐蝕裂紋。
  14. The formation of 3. 5 % nacl solution is almost similar to that of 3. 5 % nacl thin electrolyte layer, just the mass transfer rate of the oxygen in the layer is more quicker than in the solution ? the test shows that the crack growth rate of wet - corrosion fatigue of lc4cs aluminum alloy in the layer is quicker than in the solution, and also shows that morphology of fatigue fracture in the layer is evidently distinguished from in the solution

    3 . 5 nacl溶液和3 . 5 nacl薄液層的化學組成幾乎完全相同，只是薄液層中氧的傳質速率較快。實驗結果顯示了在薄液層中， lc4cs鋁合金的濕腐蝕疲勞裂紋擴展速率，大於在3 . 5 nacl溶液中的速率。實驗還發現其疲勞斷口的形貌，也與3 . 5 nacl溶液中的有明顯區別。
  15. Refining importing the high sulphur crude oil in recent years, more and more interior surface stress corrosion crack were found in the oil refining sphere

    摘要由於煉制進口中東高硫原油，在近幾年的煉油球罐檢驗中發現越來越多的內表面應力腐蝕裂紋。
  16. Testing of copper alloys ; stress corrosion cracking test using ammonia ; testing of components

    銅合金的檢驗.用氨作應力腐蝕裂紋試驗.成分的檢驗
  17. Testing of copper alloys ; stress corrosion cracking test in ammonia, testing of tubes, rods and profiles

    銅合金的檢驗.管材棒材和型材氨中應力腐蝕裂紋試驗
  18. Corrosion of metals and alloys - evaluation of stress corrosion cracking by the drop evaporation test

    金屬和合金的腐蝕.採用滴水蒸發試驗對應力腐蝕裂紋的評估
  19. At present, the distance of the pipelines running in the industry of oil refining, petrol - chemistry and electricity in china is around 500, 000 kilometres. the majority of them last one or two decades, gradually resulting in the summit of accidents with various degrees of erosion and cracks

    我國石油、化工等行業的在役油氣長輸管道總長約50萬公里，其中大部分管道已使用10 ? 20年以上，出現不同程度的腐蝕、裂紋等缺陷，逐漸進入事故高發期。
  20. Aluminium alloys. stress corrosion cracking of thick products

    鋁合金.厚產品的應力腐蝕裂紋
分享友人
分享到 Line

分享到臉書