蒸汽再熱器 的英文怎麼說
中文拼音 [zhēngqìzàirèqì]
蒸汽再熱器
英文
steam reheater- 蒸 : Ⅰ動詞1. (蒸發) evaporate2. (利用水蒸氣的熱力使食物熟或熱) steam Ⅱ名詞[中醫] (將藥物隔水蒸熟) steaming
- 汽 : 名詞1. (由液體或某些固體變成的氣體) vapour2. (水蒸氣) steam
- 再 : 副詞1 (又一次) another time; again; once more 2 (表示更加) still; further 3 (表示如果繼續怎...
- 器 : 名詞1. (器具) implement; utensil; ware 2. (器官) organ 3. (度量; 才能) capacity; talent 4. (姓氏) a surname
- 蒸汽 : vapour; reek; breath; steam蒸汽採暖 steam heating; 蒸汽錘 [機械工程] steam hammer; 蒸汽打樁鍾 ste...
-
This is accomplished by using a thermocompressor to recycle regenerating steam through the absorber.
它用熱壓機使再生蒸汽經吸附器循環來完成。In the whole system, the inner leak system is occurred to the lower pressure bypass system, this will directly cause the high quality reheated steam to reach to condenser, meanwhile increase the heat load of condenser, and the economy benefit of the unit will decreased
整個系統存在的內漏主要是低壓旁路低壓旁路的泄漏,直接造成了高品質的再熱蒸汽短路到凝汽器,同時增加了凝汽器的熱負荷,對機組經濟性的影響較大。After researching the part thermal equipments and systems include heaters, steam leakage and receiving systems, low pressure drain system etc, and computing the efficiency of the systems, find out the better choice of the imported assemblies than the domestic assemblies in parameter and the disfigurements in design and making. based on the above, point out the measure to progress them. according to the analysis, we can get some measures to increase the economical level of the systems and save more energy
對局部熱力設備及熱力系統進行分析研究,包括:加熱器設備、漏汽及回收系統、低加疏水系統、主、再熱蒸汽系統以及凝汽器等部位;並計算汽輪機本體高、中、低壓缸效率,藉此著重對汽輪機通流部分進行了剖析,找出國外進口機組動、靜葉柵、葉型的選擇比國產機組先進性以及國產機組在通流部分設計和製造中的諸多缺陷,並且指出了改進的方向,為機組提高熱經濟性、節能降耗奠定了理論基礎。To the steam generator a heat exchanger, which converts the feed water in the secondary circuit to high - pressure steam at about 67 bar or 6 700 kpa and deliver it to the " conventional island " via steam pipe for driving the turbine and generator
內的高壓水帶到蒸汽發生器即熱交換器,蒸汽發生器會將二迴路給水轉化為約67巴或6 700千帕的高壓蒸汽,再經過蒸氣管送到常規島,以推動渦輪發電機。To the steam generator ( a heat exchanger ), which converts the feed water in the secondary circuit to high - pressure steam at about 67 bar ( or 6 700 kpa ) and deliver it to the " conventional island " via steam pipe for driving the turbine and generator
內的高壓水帶到蒸汽發生器(即熱交換器) ,蒸汽發生器會將二迴路給水轉化為約67巴(或6700千帕)的高壓蒸汽,再經過蒸氣管送到常規島,以推動渦輪發電機。The mainly works had been done as follows : 1. in order to keep commonality, the modules who have similar thermodynamic process had been classed. such as evaporating module ( including furnace, drum, system of boiler recycled water ), single - phase heat exchange module ( including superheater, reheater, ecomomizer ), lubricating oil system module ( can be used for any lubricating oil system of rotation mechanical impedance ), pump and fan module, ect
本文所作的主要工作如下: 1 、為保證模塊的通用性,對鍋爐有相似熱力環節的模塊進行分類,建立模塊庫,便於模塊調用,如蒸發區模塊(包括爐膛、汽包和爐水循環系統) ,單相換熱模塊(包括過熱器,再熱器,省煤器等) ,潤滑油系統模塊(可用於各種轉機軸承潤滑油的動態特性的計算) ,泵與風機的動態計算模塊等。The authors first apply basic theory of equivalent heat drop on the common circulation heat calculating model for thermal system in supercritical pressure power unit with second reheat cycles and other kind of condensing steam turbine by mathematical derivation strictly, based on the normal energy balance and theory of equivalent heat drop, aiming at characteristics of thermal system in which there are outer steam coolers that high pressure heater and low pressure heater carry
摘要以常規熱平衡方法和等效熱降理論為基礎,針對二次再熱超臨界機組熱力系統高低壓加熱器均設置外置式蒸汽冷卻器的特點,經過嚴格的數學推導,將等效熱降理論應用於二次再熱超臨界機組熱力系統循環吸熱量計算的研究,並提出了適用於不同類型凝汽式機組的通用數學計算模型。In place of the reboiler, a heating coil may be placed in the bottom of the column to generate vapor from the pool of liquid there
例如可以在精餾塔的底部安裝一個加熱盤管代替再沸器,加熱釜液產生蒸汽。The break was assumed to be a single tube double - ended and three - tube double - ended shear break. the diameter of the break orifice is 0. 876mm and 1. 518mm respectively. the characteristic responses of main thermal - hydraulic parameters, such as primary pressure, secondary pressure, break flow rate, pressurizer level, secondary side level of steam generator and so on, were presented in this thesis
試驗再現了核電廠蒸汽發生器單根傳熱管雙端斷裂事故和三根傳熱管雙端斷裂事故發生后的熱工水力現象,給出了事故過程中一次系統壓力、二次系統壓力、破口流量、蒸汽發生器二次側水位、穩壓器水位、元件表面溫度等主要參數的瞬態響應。分享友人