螺旋齒輪型 的英文怎麼說

中文拼音 [luóxuánchǐlúnxíng]
螺旋齒輪型 英文
helical gear type
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 螺旋 : 1 （具有螺紋的圓柱體 屬于斜面類的簡單機械） corkscrewspin; screw; spiral; helix 2 （螺旋現象;尾旋...
  • 輪型 : bicycle tires
  1. Basing on the premise that the capability of the transmission and the technique are synthetically considered, three new kinds of gear pairs is given, that is, loxodromic normal circular - arc spiral bevel gears, geodetic normal circular - arc spiral bevel gear, and hyperbolic normal circular - arc gear

    在綜合考慮傳動性與工藝性等要求的前提下，提出斜航式與測地式法向圓弧螺旋錐齒輪傳動、雙曲型法向圓弧齒輪傳動等兩類三種齒輪副的構思。
  2. This essay takes the method of listing equations of gears " surface directly and installing them in appropriate coordinate system to establish the mathematic model for analyzing engagement of spiral helical gear. programs use this mathematic model to make numerical computation as well as to output the contact domains diagram and the relative velocity diagram on this foundation

    本文採用直接列寫齒面方程、在適當的坐標系中安裝的方法，建立了螺旋齒輪嚙合分析的數學模型，編製程序利用該數學模型進行數值計算，並在此基礎上輸出接觸區圖和相對速度圖。
  3. This paper develops a mathematical model for the solution to the longitudinal tooth curve of an internal gear shaver based on the simplified principle for space transmission of a helical gear pair without flank clearance, and proposes a calculating approach of the profile modification of the grinding wheel to be used for grinding the longitudinal tooth curve of the shaver

    摘要用簡化的空間螺旋齒輪作無側隙嚙合傳動的原理，建立了求解內剃齒刀齒向曲線的數學模型，並給出了修磨這種齒向曲線的盤形砂輪的廓形計算方法。
  4. Single speed motor drive connected to a helical worm gear and a totally enclosed connecting gear box with heavy duty chain drive to the rolls and with fixed friction ratio according to customers request ( normally 1 : 1, 2 )

    系統帶有同螺旋渦齒輪以及全封閉齒輪箱的單速馬達，它帶有重型鏈傳動系統並可根據客戶的需要固定摩擦比（通常為1 : 1 . 2 ） 。
  5. Normal section linear diagram of two gears " surfaces, which is on the arbitrary section, has also been protracted. the writing validated the correctness of the mathematical model and experimenting on contact region of spiral helical gear ' s surface validates theoretical analysis

    利用計算機模擬了兩齒面在三維空間中接觸的情景；描繪了三維空間中相對速度的大小及方向；繪制了任意法截面上兩齒面法截線的圖形。對螺旋齒輪齒面接觸區進行了實驗研究，驗證了本文中數學模型及理論分析的正確性。
  6. The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given

    本論文主要包括以下內容：介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系，分蝸桿固定和定子固定兩種情況，給出了這種新型傳動的傳動比計算公式，得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系，從而為該傳動的優化打下理論基礎。
  7. First, the mathematical model of tooth surface has been established by the machining process spiral bevel gears, consequently, the data of tooth surface have been gained

    本文首先從分析螺旋錐齒輪的加工過程入手，建立齒面的數學模型，從而得到齒面的數據。
  8. The power of the diesel engine is transmitted to the rudder propeller through an elastic coupling, a clutch and the universal shafts, the rudder propeller transmits the engine power to the propeller via upper and lower bevel gear sets ( z - drive )

    原動機（柴油機）的推進動力通常是通過高彈性聯軸器、離合器、萬向傳動軸送到舵槳，舵槳將動力通過上、下兩對螺旋錐齒輪付傳送到螺旋槳，從而產生推力（ z型推進） 。
  9. The two key factors, machining methods and machine - setting parameters of sbg, which are related with the generation of theoretical tooth surface and topographic deviation for sbg, are analyzed in details. after building the machine - tool mathematical model and computing the tooth surface parameters, using the given conditions and mesh equation, the coordinates of the theoretical tooth surface of sbg can be computed, and, then, the theoretical tooth surface model of sbg is derived

    本文詳細地分析了形成螺旋錐齒輪理論齒面及產生拓撲誤差的兩個關鍵因素，即螺旋錐齒輪的切齒加工方法和機床調整參數;通過建立機床數學模型，計算齒面參數，用已知條件和嚙合方程進行聯合求解，得出了理論齒面的坐標值，從而獲得了螺旋錐齒輪的理論齒面模型。
  10. ( 4 ) rough cutting and accurate cutting can be completed at the same machine which saves the investment. since klingelnberg cycloid bevel gear has these characteristics, it has special advantages and economic benefit for machines in mine, metallurgy and petroleum

    鑒于克林貝格擺線錐齒輪的這些優點，在重礦、冶金石油機械等大型機械中採用該種齒制的螺旋錐齒輪具有良好的技術優勢和經濟性。
  11. The company mainly produces auto transmission and driving axle spiral bevel gears with the production capacity of 110 thousand units and 160 thousand sets

    主要生產汽車變速器和后橋螺旋傘齒輪，具有年產11萬臺輕型車變速器和16萬套后橋螺旋傘齒輪的生產能力。
  12. Shandong automobile gear general factory is a state - owned big - scale ( ii ) enterprise and a specialized gear manufacturer for spiral bevel gears of automobile rear axle, engineering mechanical gears and gears of diesel engines, with the biggest scale, highest product precise and strongest heat treatment capacity in shandong province

    山東汽車齒輪總廠屬國家大型（二）企業，是山東省汽車后轎螺旋錐齒輪、工程機械齒輪和各種柴油發動機齒輪規模最大、精度最高、熱處理能力最強的齒輪專業生產企業。
  13. The mathematical model of loaded tooth contact analysis of spiral bevel gears has been established based on elastic dynamics and the dimensional finte element analysis method

    基於彈性力學和有限元法，建立了螺旋錐齒輪加載接觸分析的數學模型。
分享友人
分享到 Line

分享到臉書