表盤刻度 的英文怎麼說

中文拼音 [biǎopánkèdù]
表盤刻度 英文
meter scale
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  • 盤 : Ⅰ名詞1 （盤子） tray; plate; dish 2 （形狀或功用像盤的東西） sth shaped like or used as a tray pl...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. If single scale instruments are used, the low scale instrument should be 0-3 volts and the high scale instrument may be 0-20 volts.

    如果使用單刻度儀表，在低度盤上的分度是03伏，高度盤上的是020伏。
  2. If single scale instruments are used, the low scale instrument should be 0 - 3 volts and the high scale instrument may be 0 - 20 volts

    如果使用單刻度儀表，在低度盤上的分度是0 3伏，高度盤上的是0 20伏。
  3. A graduated surface or face on which a measurement, such as speed, is indicated by a moving needle or pointer

    標度盤有刻度的表面或面，在上面由活動的指針或指示器表示度量衡，比如溫度
  4. Wind : most meteorological stations are equipped with combined vane and cup generator anemometers with dial indicator and or chart recorder for wind speed and direction measurement

    風：大多數臺站都設置風向標及磁感風杯風速表來量度風向和風速，並附有刻度盤或圖表記錄器。
  5. Stationary brushed steel bezel is accented with gold plated highlights and engraved markers. attractive black dial with luminous hands and hour markers

    堅固的打磨鋼制的嵌玻璃強調在主要部分和刻度鍍金。漂亮的黑色表盤與發亮指針和時針為一體。強調在主要部分和刻度鍍金？ ？ ？ ？ ？ ？ ？
  6. Aircraft equipment. on board instrument with round dials. general dimensions

    飛機設備.圓刻度盤機載儀表.通用尺寸
  7. Aircraft equipment. on board instrument with round dials, mechanical transmission tachometer

    飛機設備.圓刻度盤機載儀表.機械傳動式轉速表
  8. A laminated safety pane, unbreakable partition between the measuring system and dial and a blow - off back cover help to prevent accidents caused by escaping media or projected parts and thus injuries to employees if a pressure overload of the gauge occurs

    測量系統和刻度盤之間有夾層安全玻璃不易破損的隔斷和吹氣后蓋。這樣，當壓力表壓力過載時，能夠防止介質泄漏或設計部件故障引起的事故，避免對員工造成傷害。
  9. In order to guarantee the request of accuracy of the work piece, all the series radial riveting machine are can add the tiny - scale device, the scale regulator are divided three kinds of specifications, they are 20mm, 30mm and 60mm. the different number representative different stroke of power head. each of scale representative the perpendicular distance 1 mm

    為保證鉚接加工精度的要求，我公司可為客戶提供加裝刻度調節的服務，現將刻度盤的參數規格公布如下，標尺可分為20mm 30mm 60mm三種規格，分別對應不同工作行程的機型，每刻度代表1mm的垂直距離。
  10. The scale is marked to show the strength of the current in amperes

    刻度盤上的刻度表示電流強度的安培數。
分享友人
分享到 Line

分享到臉書