裂縫尺寸 的英文怎麼說

中文拼音 [lièféngchǐcùn]
裂縫尺寸 英文
flaw size
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
  • 寸 : Ⅰ量詞（長度單位） cun a unit of length （=1/3 decimetre）Ⅱ形容詞（極短或極小） very little; very ...
  • 裂縫 : 1. （裂開的縫兒） rent; rip; hiatus; tear; rift; crevice; crack; fissure 2. [地質學] fracture; rupture
  1. Variation ratio of dimensional after water rinse, ultimate strength, neps and pile, tearing resistance, bursting strength, joint strength, commissure ' s swerve strength, fabric shift ( slip ), ventilate degree, elasticity ( resilient rate / deformation rate ), anti - water permeability ( hydrostatic pressure ), extension and resilience, abrasive resistance, gets wet the nature, hydroscopicity, stock ' s transverse ductility, fire resistance, antistatic

    水洗尺寸變化率（縮水） ，斷裂強力，起毛起球，撕破強力，彈子頂破強力，脹破強度接縫強力，縫口脫開程度，紗線滑移性能（滑脫） ，透氣量，彈性（回復率/變形率） ，抗滲水性（靜水壓） ，延伸及回復性，耐磨性，沾水性，吸水性，襪子橫向延伸，阻燃性能，抗靜電。
  2. Abstract : in view of the quantity examination of weld defect by ultrasonic, on the basis of theoretical analysis and test, the cause, composition and contriling method of error of crack defect size h have been analyzed systematically, a controlling and statistical method of ultrasolic examination error has been put forward. this method is simple and suitable, and has been verified by test

    文摘:針對焊縫缺陷超聲波定量檢測，從理論分析與實驗出發，系統分析了裂紋類缺陷自身高度尺寸h的檢測誤差的物理成因、組成及誤差控制方法，提出了一套實用簡潔並經實驗證實可行的超聲波檢測誤差控制及統計方法。
  3. In this research the method to test and evaluate the gic of the stitched - fabric - enforced laminates, the definition of the stitching - parameters, the testing clap were discussed according to the standard of astm. in addition, we got the useful experiment results of the gic by using the clap which we designed in the research

    試驗是依據現行的astm標準，並對測試夾具、試片的形狀尺寸等進行了適當改進，參照astm及jis標準中的數據處理與計算方法測試、評價了不同縫合工藝層合板復合材料的層間斷裂韌性值（ g _ （ ic ） ） 。
  4. Based on estimating the type of filtration by constructed g and fraction, and determining the fracture closed point, the parameters such as the geometry of fracture, the leak - off coefficient can be calculated, and furthermore it can direct the acid fracturing design and improve the acid fracturing technology

    通過構造g函數、函數可判斷儲層的濾失特性，確定裂縫閉合點從而得到裂縫的幾何尺寸以及濾失系數等參數，進而指導酸壓的施工設計和完善酸壓工藝。
  5. Wherefore, other two energy - based fracture parameters are put forward : the stable fracture energy gfs, indicating the average energy dissipation during the crack stable propagation and the unstable fracture energy gfu, corresponding to the crack unstable fracture stage. wedge. ? splitting specimens are tested with a view to understanding those two parameters " size effect in terms of the initial crack length a0

    本文提出兩個能量型斷裂參數即穩定斷裂能g _ （ fs ）和失穩斷裂能g _ （ fu ）分別表示裂縫穩定擴展和失穩擴展階段的能量損耗，並採用楔入劈拉試件（ ws ）對這兩個參數相對初始縫長_ 0的尺寸效應進行了分析。
  6. Microfiber polishing clothes are better at removing products imbedded into these surface imperfections, dramatically better than the larger fibers found in terry cloth towels

    （縮小的裂縫和擦傷）超纖維毛巾在去除表面的污物，比大尺寸的毛巾效果要好很多。
  7. Choosing the reasonable weld dimension : the defornation will be increased when weld dimension is added ; but if the weld dimension is too small, it will decrease reduce the load ability of weld and quicken the cooling speed of joint

    選用合理的焊縫尺寸：增大焊縫尺寸，變形也會變大；但過小的焊縫尺寸，將降低裂紋的承載能力，使接頭的冷卻速度加快。
  8. By comparing the fracture toughness ( kic ), the fracture energy ( gf ) and the crack tip opening displacement ( ctod ) of the same strength grade concrete, it is found that the values of the fracture toughness ( kic ), the fracture energy ( gf ) and the crack tip opening displacement ( ctod ), tested by three - point - bending method and wedge - split tensile method approach, so it is proved that the fracture toughness ( kic ), the fracture energy ( gf ) and the crack tip opening displacement ( ctod ) are related to its own properties such as material, specimen size, and crack size, but unrelated to the test - method

    通過比較三點彎曲法和楔入劈拉法測定的相同強度等級混凝土的斷裂韌度k _ （ ic ） 、斷裂能g _ f以及裂縫的尖端開口位移ctod ，發現兩種試驗方法測定的斷裂韌度k _ （ ic ）斷裂能g _ f以及裂縫的尖端開口位移ctod的數值接近，從而證明混凝土斷裂韌度、斷裂能、 ctod的值僅與材料、試件尺寸、裂縫尺寸等試件自身的性質有關，而與試驗方法無關。
分享友人
分享到 Line

分享到臉書