計總穿孔 的英文怎麼說
中文拼音 [jìzǒngchuānkǒng]
計總穿孔
英文
summary punch- 計 : Ⅰ動詞1 (計算) count; compute; calculate; number 2 (設想; 打算) plan; plot Ⅱ名詞1 (測量或計算...
- 總 : Ⅰ動詞(總括; 匯集) assemble; gather; put together; sum up Ⅱ形容詞1 (全部的; 全面的) general; o...
- 穿 : Ⅰ動詞1 (破; 透) pierce through; penetrate 2 (通過孔、隙、空地等) pass through; cross; go thro...
- 穿孔 : 1 (鉆孔; 鑿孔; 打孔) bore a hole; punch a hole; punching; piercing; tresis; key punching 2 [醫...
-
In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys
本文首先對子母式穿甲彈總體參量作了全面的計算分析,其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度,論證了子母式穿甲彈對付爆炸式反應裝甲的可行性,然後對子母式穿甲彈彈頭部進行了總體設計,其中主要對子彈的發射過程進行了詳細的分析,得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系,設計出了合理的母彈彈頭部結構和子彈的結構,並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。In order to break through the traditional technology and the conception of equipment design, suggest to use bunchy phase deep hole or big diameter deep hole in laneway to realize the exploding of high step on opencast working ; digging with big contain forklift to realize the continuous transportation of dragline - mobile convolution crusher - belt transportation machine, therefore form a new technology system that be propitious to increase collectivity technique and economic benefit
為突破基於常規工藝和設備配套的設計理念,推薦採用束狀階段深孔或在巷道中採用大直徑深孔的方法實現露天開採的高臺階穿爆作業;採用大斗容索鏟下挖作業實現自工作面開始的索斗鏟移動式旋迴破碎機帶式輸送機的連續運輸工藝,從而形成有利於提高露天開采設計總體技術經濟效果的新的工藝技術系統。In joist ' s temporary fixation, if temporary bolt and drill nail are used, amount of them should be calculated as flowed specification : the amount should be no less than 1 / 3 of all holes ; at least, two temporary bolts should be used ; amount of drill nail should be no more than 30 % of temporary bolts bolted ( grade a, grade b ) hole shouldn ' t be fixed with drill nail
桁架臨時固定如需用臨時螺栓和沖釘,則每個節點處應穿入的數量必須由計算確定,並應符合下列規定:不得少於安裝孔總數的1 / 3 ;至少應穿兩個臨時螺栓;沖釘穿入數量不宜多於臨時螺栓的30 % ;擴鉆后的螺栓( a級、 b級)的孔不得使用沖釘。
分享友人