試樣棒 的英文怎麼說
中文拼音 [shìyàngbàng]
試樣棒
英文
test bar-
We could use bonzi this game
這樣的比賽我們應該試試棒子!Plastics - injection moulding of test specimens of thermoplastic materials - small tensile bars
塑料.熱塑材料試樣噴射鑄造.第2部分:小拉伸棒料Well. it would be nice to get away from this cold weather and just lie in the sun and relax after working so hard
是這樣。沉重的考試后,避開這么冷的天,到太陽下躺著休息一定棒極了。W : well. it would be nice to get away from this cold weather and just lie in the sun and relax after working so hard
是這樣。沉重的考試后,避開這么冷的天,到太陽下躺著休息一定棒極了。Standard practice for preparation of bar and rod specimens for adhesion tests
附著力試驗用棒和桿試樣制備的標準操作規程The difference among the elasticity modulus of various microstructures is probably the main reason, which caused the experiment results above. under the same experiment conditions, such as sample shape, size, surface roughness, establishment of testing system, pressure on the probe, and thickness of coupling medium, the variety of relative attenuation coefficient ( or ) in different heat treatment samples is measured and compared by measuring the attenuation obtained from the cylindrical surface of column. the result is as following : for 40cr and 38crmoal, a mt < az mq < a s < a p + f ; for gcrlssimn, a mt < a annea < s < a p + f ; and a increased with the increasing of frequency
在保證試樣形狀、尺寸、表面光潔度、系統參數設置、施加在探頭上的壓力以及耦合層厚度等測試條件一致的情況下,利用棒材圓柱面測衰減系數法,分別測定並比較上述不同熱處理試樣相對衰減系數的變化情況,得到的實驗結果是:對於40cr及38crmoal鋼, _ (低溫回火) (淬火) _ (高溫回火) _ (正火) ;對于gcr15simn鋼, _ (低溫回火) _ (退火) _ (高溫回火) _ (正火) ;且隨著頻率的提高,衰減系數均呈現增加的趨勢。Standard test method for comparing bond strength of steel reinforcing bars to concrete using beam - end specimens
用梁端試樣比較混凝土和鋼筋棒粘結強度的標準試驗方法Measurement of fracture toughness of pmma by using circumferentially notched round - bar specimens
切口圓棒試樣測聚甲基丙烯酸甲脂斷裂韌性可行性分析Experimental results show that after reducing the dependency of features, sa method works better. the most three important features of the license plate regions are obtained in the experiment and our algorithm is robust in filtering out false plate regions. in the module of binarization of license plate, based on algorithm of casda ( cluster algorithm based on spatial distribution analysis ) an improved quick binarization algorithm i - casda are proposed to get rid of the influence of the illumination
運用本演算法對復雜背景的車輛牌照進行檢測,實驗結果表明,基於簡單平均融合運算元的檢測演算法得到的檢測率高, 80 . 36 (訓練樣本)和76 . 54 (測試樣本) ,平均檢測速度為每幅圖象0 . 81秒,滿足實時性要求;區域寬高比、區域密度和區域寬度比率是車牌區域最重要的三個特徵;本演算法魯棒性好,可較好地排除相似紋理區域(如廣告牌等)的干擾。Examinations show that our arithmetic can make good use of hvs system, and is robust to common image processing such as noise, mean - filter, sub - sample and jpeg compress. string - type watermark is more robust
經過試驗檢驗,該演算法不僅能很好地結合hvs系統,且對一般圖像處理(對抗噪聲、均值濾波、亞抽樣和jpeg壓縮)都具有好的魯棒性,字元型水印的效果更佳。This step should be also should be repeated for non - ferrous sensitivity test stick. ensure all test pieces are removed from finished product pack, after the test has been successful
此步驟對于非鐵敏感測試棒同樣適用.檢測成功后要確保所有的測試片都從完成檢測的產品中拿走Plastics. injection moulding of test specimens of thermoplastic materials. part 2 : small tensile bars
塑料.熱塑材料試樣的注模.第2部分:小拉伸棒Plastics - injection moulding of test specimens of thermoplastic materials - part 2 : small tensile bars
塑料.熱塑性塑料試樣的注射模塑件.第2部分:小拉伸棒Plastics - injection moulding of test specimens of thermoplastic materials - part 2 : small tensile bars iso 294 - 2 : 1996 amd. 1 : 2004 ; german version en iso 294 - 2 : 1998 a1 : 2005
塑料.熱塑性材料試樣的注模塑法.第2部分:小拉伸棒Methods of testing plastics - dimensional properties - determination of shrinkage of test specimens in the form of bars of compression moulded thermosetting moulding materials
塑料的試驗方法.尺寸特性.熱固性模製材料在壓模製棒材過程中試樣的收縮量測定Plastics - injection moulding of test specimens of thermoplastic materials - part 1 : general principles, and moulding of multipurpose and bar test specimens
塑料製品.熱塑性材料試樣的注模.第1部分:一般原則多用途模製法及棒材試樣Plastics - injection moulding of test specimens of thermoplastic materials - general principles, and moulding of multipurpose and bar test specimens
塑料.熱塑材料試樣噴射鑄造.第1部分:一般原則多用途棒材試樣模鑄分享友人