誤差敏感元件 的英文怎麼說

中文拼音 [wùchāmǐngǎnyuánjiàn]
誤差敏感元件 英文
error sensor
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 敏 : Ⅰ形容詞（靈敏;敏捷） quick; agile; smart; nimble Ⅱ名詞（姓氏） a surname
  • 感 : Ⅰ動詞1 （覺得） feel; sense 2 （懷有謝意） be grateful; be obliged; appreciate 3 （感動） move; t...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 誤差 : error
  • 敏感 : sensitive; susceptible; tactful
  1. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  2. Nevertheless, the widely existed overconstraints in the mechanisms will make the quality of the mechanisms very sensitive to the inevitable manufacturing, assembly errors ( especially, the errors resulted from the shape and position between kinematic pair elements and their axes ). at the same time, because the internal and external uncertain factors such as non - plane characteristic of dynamic parameters of links ( such as mass distribution, inertia forces, etc. ), bending and twist of links, and the changes of environment and operating condition are inevitable, they will form the disturbance to planar constraints and make them possess the characteristic of " uncertain "

    但是，平面連桿機構中廣泛存在的過約束，造成機構對製造、安裝誤差特別是運動副元素的形位誤差十分敏感；同時，由於不可避免的內部和外部不確定因素的影響，常常會造成機構運動的「障礙」及系統中某些構件的變形和運動副中的附加動載荷，引起機械的振動、沖擊、噪聲等而導致機械的效率和工作性能的降低。
分享友人
分享到 Line

分享到臉書