誤差橢球 的英文怎麼說

中文拼音 [wùchātuǒqiú]
誤差橢球 英文
error ellipsoid
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 橢 : Ⅰ形容詞（卵形） oval-shapedⅡ名詞[書面語] （長圓形的容器） elliptic vessel
  • 球 : 名詞1 （以半圓的直徑為軸 使半圓旋轉一周而成的立體; 由中心到表面各點距離都相等的立體） sphere; glo...
  • 誤差 : error
  1. Based on the method expressing the positional uncertainty of point entities in surveying and mapping, uncertainty ellipse was employed to characterize the uncertainty region for the error dispersal of 2d target ' s position, and uncertainty ellipsoid for the 3d target. 1 - uncertainty ellipse was derived from positional error covariance

    借鑒測繪學科中衡量點元位置不確定性的方法，分別用橢圓和橢球來表示二維目標和三維目標的位置誤差散布的不確定性區域。
  2. To eliminate or lessen the system errors caused by the offset and slope of the thin aluminum sheet when measuring its surface, and to avoid over - cutting while machining the honeycomb surface, the saddle - point programming is applied to the position optimization of the theoretical surface. to generate the cnc program of the honeycomb sandwich, the equidistant calculation of the actual surface is produced and the data processing software is developed

    利用鞍點規劃方法優化理論橢球面的位置，使實測曲面相對理論橢球面的最大法向誤差達到最小，減少或消除了蒙皮內表面測量時由於定位的偏心或歪斜引起的系統誤差，使誤差均化，防止了配對加工蜂窩夾芯表面時少切或過切現象的發生。
  3. To machine the honeycomb sandwich, an interpolation method based on a rotary axis is also studied. with the round vector function and rotary movement group, a model of the error curved surface of the theoretical ellipsoid is set up to describe the actually measured surface

    以圓矢量函數和回轉運動群為工具討論了曲面的誤差變換，利用理論橢球面的誤差曲面建立了實測曲面的數學模型，通過求解理論曲面的法線實現了實測曲面的等距計算和陰陽面數據轉換。
  4. As the inner shape of the thin aluminum alloy sheets will deform and differ from the theoretical ellipsoid to some extent after welding processing, it is very difficult to meet the requirements of the tolerance between the honeycomb sandwich and thin aluminum sheets when only conventional cnc and traditional manual manufacturing techniques are used

    由於上、下底蒙皮焊接成型過程中的變形使其內表面形狀相對于理論橢球面具有較大的誤差，採用常規的橢球面數控加工方法，或傳統的按上底蒙皮內表面手工打磨、研合修配方法加工蜂窩夾芯表面無法保證配合精度要求。
  5. Admissibility of nonnegative quadratic estimators for error variance with respect to restricted ellipsoidal parameter space

    橢球約束下誤差方差非負二次估計的可容許性
分享友人
分享到 Line

分享到臉書