誤差相對極限 的英文怎麼說
中文拼音 [wùchāxiāngduìjíxiàn]
誤差相對極限
英文
relative limit of error- 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
- 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
- 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
- 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
- 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
- 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
- 誤差 : error
- 相對 : 1. （面對面） opposite; face to face 2. （非絕對的） relative 3. （比較的） relatively; comparatively
- 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
-
4. the thrust measurement device was calibrated, and the accuracy was 2 % fs. at the same time the signal of thrust measurement was input to the computer. e - type chromel - constantan thermocouple was used to measure the temperature of mpt, and the accuracy was 5 % fs. the vacuum measurement was realized by using zdf - 5427m vacuometer, and the accuracy was 3 % fs
（ 4 ）對推力測量系統進行了標定並實現了計算機採集，推力測量系統最大相對誤差為2 fs ；溫度測量目前還只限於對mpt諧振腔壁溫的測量，使用e型鎳鉻?康銅熱電偶即可較容易實現，其測量精度為5 fs ；真空測量採用zdf - 5427m微機型復合真空計，其由熱偶計和熱陰極電離計復合而成，該真空計測量控制精度為3 fs 。Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性Initial rotational stiffness ri and ultimate moment capacity mu of top - and seat - angle steel connections is given in this text. initial rotational stiffness rt and ultimate moment capacity mu of top - and seat - angle with double web - angle steel connections is given in this text. it is right by comparison with experiment
推導了頂底角鋼、腹板雙角鋼連接的初始連接剛度r _ i ，頂底角鋼、腹板雙角鋼連接的極限彎矩承載力並經和試驗比較得出兩種連接型式的初始連接剛度、極限彎距承載力其理論值和試驗值的相對誤差在工程允許的范圍內。
分享友人