諧振電壓 的英文怎麼說
中文拼音 [xiézhèndiànyā]
諧振電壓
英文
resonance voltage- 諧 : Ⅰ形容詞1 (和諧) in harmony; in accord; in tune 2 (詼諧) humorous Ⅱ動詞(商量好; 辦妥) come t...
- 振 : 動詞1. (搖動; 揮動) shake; flap; wield 2. (奮起) brace up; rise with force and spirit
- 電 : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
- 壓 : 壓構詞成分。
- 電壓 : voltage; electric tension; electric voltage
-
The way of taking one nth out of capacitor ' s the first harmonic capacitive reactance as its nth harmonic impedance is verified whit the data from tang7c. according to the approximately estimating method, the first harmonic impedance of 220kv system is calculated. on the basis of the models, this paper gives the harmonic equivalent circuit of substation and gives the b ( n ) function of the harmonic time n. when the capacitors has different combination, b ( n ) ' s value will also change, with the inputting local measurement data, the paper studies the series and parallel resonance at the substation, and deduces that the reason the capacitor ' s fuse of tang6c is frequently interrupted is that its capacitor current contains a large number of 5th harmonics, and that the reason the discharging pt of tang7c capacitor being exploded is also that the 7th and 9th harmonic currents are amplified
據此,對該站進行了串聯諧振分析和並聯諧振分析,並結合測試數據和有關變電站的運行記錄,指出了導致該站電容器湯6c頻繁燒保險的主要原因是5次諧波電流含量偏高,引起湯7c放電pt爆炸也是因為7次和9次諧波電流被放大。針對這些導致湯陰變電站補償電容器故障的原因,提出了相應的諧波治理措施,包括針對湯6c電容器5次諧波電流含量偏高的原因,提出了停運湯6c電容器或者通過把湯sc電容器的部分容量併入湯6c電容器(湯sc其餘部分停運)以增加湯6c諧波承受能力的措施;針對# 2變低壓側7次和9次諧波電流被放大的現象,提出了在湯7c電容器上加裝一定百分比的串聯電抗器的措施。Precise thickness - shear resonance frequency of electroded piezoelectric crystal plates and its applications in resonator design
帶電極壓電晶體板厚剪共振頻率的精確確定及其在諧振器設計中的應用Iron - magnetic resonance of electromagnetic - type potential transformer of 10 kv power system for yamzho yumco pumped storage station
系統電壓互感器引起的鐵磁諧振及消諧方法The device has more advantage than traditional adjustable ac high voltage design. it adopts adjustable method to make adjustable series resonance even easier and the change extend of tested much wider. it is fit to test the majority of electricity system design
該裝置與傳統的調感式交流高電壓裝置相比具有更多優點,採用調頻方法使調節諧振更容易,被試品的變化范圍可以更大,適合大多數電力系統裝置的試驗。1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %
從功率單向流動角度出發,提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲,在調制系數0 . 1 m 0 . 5情況下,控制移相角按正弦規律變化,使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號,經過整流、濾波、低頻逆變,從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載,移相全橋具有超前橋臂零電壓開通,滯后橋臂或者零電壓開通( _ 0 )或者零電流關斷( _ 0 )的軟開關特性,而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。Abstract : a new waveguide which can change the wide wall of a rectangular waveguide into a symmetric arc wall is named as a cam - rectangular waveguide. comparing to sectoral waveguide, the new waveguide has the same voltage characteristics and is easier to be produced and fixed. an approximate formula of the dominant mode fields and the normalized conductance of a longitudinal resonant slot cut in the curved wall of a cam - rectangular waveguide are given. a resonant slot linear array in c & x band is designed, in which the slot voltage distribution is equiphase and the input is matched. the input voltage stationary ware ratio and the h - plane pattern of the antenna are measured. the experimental results show the conformance with theoretical results
文摘:把常用的矩形波導一個寬面改成圓弧形構成的波導稱為圓突-矩形波導.這種波導與扇面波導相比:電性能相當;波導管結構更加簡單,容易加工,便於安裝.文中給出圓突-矩形波導中主模場,圓曲面上縱向槽歸一化諧振電導近似公式.設計了c和x波段波導曲面縱向諧振縫隙線陣,縫隙電壓相位為同相分佈,輸入端匹配.實際測量了天線輸入端電壓駐波比和h面方向圖,理論與實驗相吻合Zero - voltage turn - on and zero - voltage turn - off in lagging arm and leading arm of soft - switching topology, working waveform of power transformer and process of rectifier and transition are presented in detail. the influence of resonant inductance of the power transformer, resonant capacitor and variation of load to the process of soft - switching are given
主要對軟開關滯后橋臂和超前橋臂的零電壓開通、關斷過程,功率變壓器的工作波形及整流換流過程進行了詳細的模擬分析,並重點討論了逆變器的諧振電感、諧振電容以及負載變化對軟開關過程的影響。In order to eliminate the voltage oscillation caused by the reverse recovery of the rectifier diodes, a resonant inductance and two clamping diodes can be introduced to the primary side
為了消除輸出整流管的電壓尖峰,可以在原邊加入一個諧振電感和兩個箝位二極體。A lcc multi - resonant ( mr ) network is added to the traditional three - level converters to realize zvs. the unique arrangement of a multi - resonant network results in absorption of all major parasitic components hi the resonant circuit, such as transistor output capacitance, diode junction capacitance and transformer leakage inductance, which can eliminate parasitic oscillation in the converter
它的優點在於諧振電容吸收了開關管和續流二極體的結電容,諧振電感吸收了變壓器的漏感,使得開關管和續流二極體都能在軟開關的條件下完成導通和關斷過程,消除了電路中的寄生振蕩。In chapter 4, considering the features of high voltage transformer and the difficulties to make it, a reasonable design scheme with src was proposed, which efficiently reduced negative influence of distributing parameters of transformer on switching power supply and could completely utilize leakage inductance as resonant inductance
第四章中分析了高頻高壓變壓器的特點及難點,提出了合理的串聯諧振變換器的設計方案,能夠完全利用變壓器的漏感作為諧振電感,有效地降低了分佈參數給高壓大功率開關電源所帶來的不利影響。By compared with the simulation results and the experiment results, we come to the conclusions that : ( 1 ) circuit with assistant network can widen soft - switching extent in lagging arm, reduces duty - cycle loss on the secondary, diminishes switching dissipation of inverter spot - welding power source. ( 2 ) the range of resonant capacitor, the important factor to soft - switching process, not only affects zero - voltage turn - off of power switches, but also affects the range of zero - voltage turn - on of power switches. so resonant capacitors must be considered according to many aspects ; ( 3 ) it easily fulfils soft - switching condition in lagging arm as leakage inductance of power transformer increases, but bigger leakage inductance of power transformer increases opening dissipation of transformer and decreases efficiency of soft - switching inverter power source
通過模擬結果與軟開關點焊逆變器試驗結果的對比分析,得到了如下主要結論:採用輔助網路可以完全拓寬全橋軟開關逆變器的滯后橋臂軟開關范圍,減小了次級占空比丟失,降低了逆變電阻點焊電源的開關損耗;諧振電容是影響軟開關工作狀態的重要因素,其大小不僅影響開關管的零電壓關斷,同時也影響開關管的零電壓開通范圍,因此,諧振電容應該綜合考慮;功率變壓器漏感越大,越容易滿足滯后橋臂的軟開關條件,但是大的漏感也使變壓器的通態損耗增加,降低了軟開關逆變器的效率。Key points in application of jszbf type anti - ferromagnetic resonance voltage transformer
型抗鐵磁諧振電壓互感器應用中需注意問題In the second chapter, equivalent circuit of the eddy current sensor is firstly analyzed. based on that, the carrier signal generating circuit that is realized by the lc periodic circuit is introduced, thus, the carrier signal of standard frequency is obtained through the trimming capacity. subsequently, the disc type rotational armature generator and the rotational coupling transformer are separately leaded in to realize the power supplies of the carrier signal generating circuit and output of the measuring signal
在傳感器設計一章中,首先對渦流傳感器進行等效電路分析,在此基礎上分析了由電感、電容諧振電路構成的載波信號發生電路,並通過微調電容獲得了標準頻率的載波信號;接下來提出了採用盤式旋轉電樞發電機解決載波信號發生電路電源供給問題的方案,同時通過旋轉耦合變壓器的引入,使得測量信號輸出問題很好地解決;本章最後給出的一組實驗曲線充分說明了這一方案的可實現性。The clamping diodes conduct only once in a switching period, and the resonant inductance current is smaller in zero state, leading to a higher efficiency and reduced duty cycle loss. the operation principle of the improved converter and the comparison with the original converter are analyzed in this paper. the effect of the blocking capacitor in series with the transformer or resonant inductance is discussed, and a best scheme is determined
本文將諧振電感和變壓器交換位置,使變壓器與滯后橋臂相連,這樣箝位二極體在一個開關周期中只導通一次,同時零狀態時諧振電感電流較小,有利於提高變換效率和減小占空比丟失,本文分析改進后變換器的工作原理,並與改進前的變換器進行對比,討論隔直電容在不同位置對變換器工作的影響,確定一種最佳工程方案。A microstructure resonant pressure sensor measures applied pressure by detecting change of resonant frequency of its mechanical resonator. the sensor is characterized by its very small size, high accuracy, excellent stability and convenient interfacing with digital electronics, showing broad application prospects
微結構諧振式壓力傳感器是通過檢測其機械諧振器諧振頻率的變化來實現壓力測量,特點是尺寸小,精度高,穩定性好,易與數字電路介面,具有廣闊的應用前景。A novel resonant pole zvt three - phase pwm inverter circuit for three - phase ac motor driving is presented. the proposed circuit has the feature of being more flexible with three inverter arms in zvt process. using only one resonant inductance, the inverter can not only reduce the power loss of inductance but also avoid possibility of unbalance in motor ' s three stator windings
提出了一種針對三相交流電機驅動的新型諧振極零電壓過渡三相pwm逆變器電路,該電路中三個逆變橋臂的零電壓過渡更具有靈活性,僅使用一個諧振電感,既減少了電感損耗又防止了電機三相定子繞組可能存在的不平衡問題,並且諧振電感中殘余能量能夠回饋給電源;新型逆變器的輔助開關均工作在零電流開關條件下,並且控制邏輯簡單。On the in - pipe locomotive mechanism using resonance piezoelectric vibrators
諧振型壓電式管內移動機構The structure of the micro differential capacitance is optimized by use of the ansys software. 3. when sih4 reacts with nh3 in a plasma - enhanced chemical vapor deposition ( pecvd ) equipment, a thin film of si3n4 is deposited on the si film
2 .研究了微電容式壓力傳感器的差動電容結構設計和微諧振式壓力傳感器的微諧振子結構設計,利用ansys軟體對微差動電容的結構進行了優化設計。In chapter three, the passive vibration control of a smart cantilever beam with piezoelectric shunt damping system is studied theoretically. in this chapter, the mechanical impedance of piezoelectric shunt damping system is analyzed, and the parameters of the rlc piezoelectric shunt circuit are optimized via transfer function of the piezoelectric shunt damped beam in order to optimize the vibration damping effect
研究了利用壓電分流阻尼系統進行壓電智能懸臂梁被動振動控制的方法,分析了壓電分流阻尼系統的機械阻抗,並通過傳遞函數方法對rlc串聯壓電分流諧振電路元件的參數進行了優化,以使壓電分流阻尼系統的阻尼效果達到最優。The influence of the resonant parameters and the input - output voltage to the converter efficiency is analyzed base the calculation. and the influence of the turn - off loss of the assistant switch to the efficiency of the typical zvt - pwm buck converter is analyzed
根據計算公式和計算結果,分析了諧振電感,主開關並聯電容和輸入輸出電壓對變換器工作效率的影響,並且詳細分析了輔助開關的關斷損耗在帶不同負載時對變換器工作效率的影響。分享友人