負壓鑄造 的英文怎麼說

中文拼音 [fùyāzhùzào]
負壓鑄造 英文
v-process
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 壓 : 壓構詞成分。
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 負壓 : [物理學] negative pressure; subatmospheric pressure
  • 鑄造 : [冶金學] cast-on outwell; foundry; cast; casting; found; founding
  1. The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting

    結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。
  2. The results show that, composite could be fabricated on the complicated surface by means of sodium silicate sand mold combination with vacuum infiltration process. when the substrate was 10 mm, composite layers reached 3 mm to 5 mm in thickness with high strength interface and less casting defect. microstructures of grey cast iron and low chromium cast iron matrix composites with various volume fraction has been analyzed

    結果表明：用水玻璃砂型（芯）加負壓鑄滲的工藝能夠實現復雜表面（曲面）顆粒增強復合材料的制備，澆注方式簡單可靠，基材厚度在10mm時，復合層厚度能達到3 5mm ，且復合層鑄造缺陷少，復合效果好，界面緻密而且結合強度高。
  3. Integrally cast body ribs, running parallel and perpendicular to the pipe axis, impart additional strength for high pressure conditions, thermal and pipe loads

    整體鑄造閥體翼肋，與管路軸線平行和垂直，增加了閥體強度，適用於高壓環境、高溫和管道負載。
  4. This thesis fabricated successfully a wc particle reinforced iron matrix composite using a vacuum infiltration process for severely erosion and application in the slurry pump. the casting process was optimized. the microstructure and wear resistance were researched and analyzed

    本文針對承受嚴重沖蝕磨損的渣漿泵過流件，採用負壓鑄滲工藝成功制備了碳化鎢顆粒增強鐵基表面復合材料，改善和優化了復合工藝、鑄造工藝。
分享友人
分享到 Line

分享到臉書