負載不匹配 的英文怎麼說

中文拼音 [fùzǎibùpīpèi]
負載不匹配 英文
load mismatching
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 不 : 名詞[書面語] （剁物所用的木墩） a block of wood
  • 匹 : Ⅰ動詞（比得上; 相當; 相配） be equal to; be a match for Ⅱ形容詞（單獨） lone Ⅲ量詞1. （用於馬、騾等） 2. （用於整卷的綢或布）
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 負載 : [電學] load
  • 匹配 : 1. [書面語] （婚姻配合） mate; marry 2. [電學] matching
  1. ( 3 ) it is known that load effect is not consistent with the section resistance incommon section continuous composite beam. a kind of composite beam with itsrational section size is suggested, which is consist of the t shape concrete beam andsteel girder. this kind of composite beam not only has enough carrying capacity, almost has same positive and negative resistance moment, but can decrease theamount of the steel

    （ 3 ）分析可知連續組合梁的跨中、支座截面處荷載作用效應及截面抗力規律不匹配，本文提出了採用t形混凝土梁和工字鋼代替一般的混凝土板和工字鋼的組合梁截面形式，並給出了截面尺寸比例，能使正負截面抵抗矩接近，符合組合梁受力特徵，減少了材料用量，滿足承載力和剛度等要求。
  2. Thirdly, it simulated the pumping circuit & dividing circuit with the widely used software matlab / simulink. the displacement of the rod piston and the impact of hydraulic are analyzed in the different input flow ( frequency of pump ) and different reversing time. it found out the cause of hydraulic impact ( one - to - one incorrespondence between the response time of dividing circuit and the operation time of rod piston ), and gave some methods to weaken hydraulic impact. in the final part of the paper, the reliability of the theory analysis is further verified by the experiment of hydraulic system

    首先在流變學原理的基礎上，深入分析混凝土在輸送管道內的流動狀態，得出混凝土泵的負載特性方程；然後根據功率鍵合圖的建模方法，建立泵送迴路和分配迴路的數學模型，並運用模擬軟體matlab simulink對泵送和分配迴路模型進行了模擬，分析了在不同的輸入流量（泵送頻率）和換向時間下，活塞桿的位移和系統的液壓沖擊情況，找到了引起液壓沖擊的根本原因（即分配迴路的響應時間（固定值）與活塞桿的運動時間（變化值）不相匹配） ，並提出了相應的改進方法。
  3. The possible factors including the deviation of temperature in length and breadth of rod, the changes of transfiguration resisting force under the changes of temperature, the adjustment of roll gap, the variation of rolling pressure, the changes of roller speed during dynamic adjusting press, the unmatched of seconds - flux under the dimension fluctuation of the coming sample and so on. the whole system was a closed loop which factors in it interacts each other

    可能的影響因素有:沿軋件縱橫向溫度變化、由溫度引起的軋件變形抗力變化、軋機輥縫值變化、負載變化、電機調節系統由不穩定向穩定過渡過程中軋輥轉速的變化（如咬鋼過程中的動態速降后的回復階段） 、來料尺寸波動造成秒流量不匹配等，整個模擬系統是各個因素相互影響關聯的一個閉環系統。
  4. Not only can gain mismatch of the sigma - delta modulator be minimized, but the overload of the later stage sigma - delta modulator can also b e resolved without sacrificing the signal noise ratios ( snr ) of the over all system

    不僅可以減輕積分三角調變器增益不匹配之困擾，並且可以解決后級積分三角調變器容易過負載之問題；然而，卻不會讓整體系統的訊號雜訊比（ snr ）降低。
  5. With the increase of the electric power system capacity as well as the short lines, high currents will possibly occur in the transmission line when a fault happens at the end of the line. the iron core of the current transformer ( ct ) will become saturated easily because of the large current, or when the secondary load of the ct does n ' t match the 10 % error curve

    隨著電力系統容量增大以及短線的增加，在電力系統線路末端發生短路時，有可能出現很大的短路電流；在很大短路電流的作用下，或由於電流互感器二次側負載與10誤差曲線不匹配等原因，電流互感器鐵芯很容易飽和。
  6. After you make sured the loudspeaker, will choose the enlarger, then make can with accuracy start this this loudspeaker. not only the enlarger s power want enough and big, but also the enlarger s electric voltage the electric current characteristic must also load the with loudspeaker to match. 100 w powers lose into the enlarger that a loudspeaker ambition for 8 ws need that enlarger, with 100 it is same that w powers lose into a loudspeaker for 2 ws

    當你確定了揚聲器之後，就要選擇放大器，以使能正確地啟動這此揚聲器。不僅放大器的功率要足夠大，而且放大器的電壓電流v - 1特性也必須與揚聲器負載相匹配。 100w功率輸進一個8w的揚聲器志需要的放大器，與100w功率輸進一個2w的揚聲器的放大器是相同的。
分享友人
分享到 Line

分享到臉書