負載測試機 的英文怎麼說

中文拼音 [fùzǎicèshìjī]
負載測試機 英文
load testing machine
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 機 : machineengine
  • 負載 : [電學] load
  • 測試 : test; testing; checkout; measurement
  1. It looks upon water resistant as load, simulate every instance of locomotive running and check its every parameter automatically, then collect and dispose these data of parameters, calculate the power of simulating running of locomotive, which is based on the current, and voltage of host dynamotor. afterward, it can be judged from the working state of locomotive. through experiment and adjust each parameter, it can provide important warrant to the components of locomotive whether they can work normally and credibly

    即以水阻作為負載，模擬機車運行，對機車的主發電動機的電流、電壓和柴油機的轉速等參數進行檢測，並對檢測結果進行處理，計算出模擬機車運行時的功率，並以此為依據，對機車的工作狀念進行判斷，通過水阻試驗，調整有關參數，使機車運行時能發揮所要求的功率和滿足規定的工作特性。
  2. Then following reality constituent of engine and connecting component interface, a nonlinear signal cylinder engine model has been created, though fire interval and fire order, a control - oriented four cylinders engine is build. following dynamometer is seen as load, performance of engine is simulated and researched under the condition of constant torque and speed, validation of the math and simulation model have been confirmed by comparison result between simulation with test result of engine performance simulation software dyno

    按照發動機的實際組成，根據各部件的介面類型連接模型庫中的部件，建立了單缸發動機非線性模型，在此基礎上，依據發動機實際發火間隔和順序，建立了面向控制的四缸汽油機模型，並以測功器為負載，通過恆轉矩和恆轉速方式進行了發動機性能模擬和研究，模擬結果和發動機動力性能模擬軟體dyno測試結果的對比驗證了數學模型和模擬模型的正確性。
  3. Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc

    能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性（壽命）試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。
  4. Single or three phase at nominal low voltage are required to be inspected, tested and certified at least once every five years. examples of such installations are power supply to lifts, water pumps, public lightings and other communal services in the common area of domestic premises and fixed installations in offices etc. having total loading exceeding 100 amperes, single or three phase

    （單相或三相）時，該裝置須每5年最少作一次檢查、測試及領取證明書。這類裝置包括住宅樓宇內升降機、水泵、公共照明及其他公用設施的供電裝置，辦公室內的固定裝置等，其總負載量超逾100安培（單相或三相） 。
  5. In this paper, the drive theory of the large ratio friction transmission is studied ; a new type elliptical cam wave generator is designed ; the large ratio friction transmission prototype is designed and manufactured ; based on the ansys finite element method software, structure of the elliptical cam is analyzed ; precision index of the manufactured large ratio friction transmission prototype, such as transmission accuracy, least step, stability of the least step, load capacity is measured by the absolute rotary encoder. by analyzing the measurement data and research content, it is think that the new elliptical cam wave generator could overcome a good many problems brought by processing errors, facilitate size precision adjustments, input moment can be achieved in the form of a pure force couple importing ; through this study, " the large ratio friction transmission prototype " could apply in practical engineering basically

    本文研究了大速比摩擦傳動的傳動理論;設計了新型橢圓凸輪波發生器，設計製作了大速比摩擦傳動樣機;用軟體ansys對所設計的橢圓凸輪結構進行了有限元分析;用19位絕對式編碼器測試了大速比摩擦傳動機構的傳動精度、最小步距、最小步距的穩定性以及帶負載能力等各項精度指標;對測量數據和研究內容進行了歸納和整理，認為新型橢圓凸輪波發生器克服了加工誤差帶來的諸多問題，新型橢圓凸輪波發生器可以進行尺寸精度調整，能夠達到輸入力矩以純力偶的形式輸入;通過本項研究，基本可以使「大速比摩擦傳動機構」在工程中得以應用。
  6. The improvement system is made up of the pressure sensor, flow sensor, displacement sensor, electro - hydraulic proportional flow control valve, power amplifier, data gathering board and computer. the platform can carry out testing the hydraulic parameters, processing the tested data, saving the processed data and drawing, adjusting the pressure automatically

    改造后的測控系統主要由壓力傳感器、流量傳感器、位移傳感器、比例節流閥、功率放大器、數據採集卡和計算機組成。改造后的實驗臺具有自動採集實驗數據、自動處理實驗數據、自動保存實驗數據、自動調節液壓系統負載壓力等功能，大大提高了實驗臺的工作效率、測試精度和智能化水平。
  7. This testing system is based on the pxi bus virtual testing system. there are many secondary types of equipments in the system. such as the programmable power supply, high voltage probe, high voltage relay, high voltage load and pneumatics

    本文以pxi總線虛擬測試系統為核心，輔以程式控制電壓源、高壓衰減探頭、高壓繼電器、高壓放電負載及氣動裝置，分別設計組裝了主機櫃與測試櫃，完成整個自動測試進程。
  8. The hydraulic resistance testbed is an important equipment for carry on diesel locomotive load performance test, adjusting diesel locomotive power and overhauling its state

    水阻試驗臺是對內燃機車進行負載性能試驗、整定機車功率、實現內燃機車狀態監測的重要設備。
  9. Sb2016 is suitable to be used as power load & standard resistance of every calibration institutions, research institutions, factories and schools, specially for testing and calibration the kinds ofwithstanding voltage tester

    適用於各計量與科研機構、工廠與學校作功率負載及電阻標準，特別適用於檢測/校準各種規格的耐壓測試儀。
  10. It analyses the causes to bright image movement, studies principle to compensate image movement, conforms project to compensate image movement, and designs framework to compensate image movement in the article ; to analyze and design configuration of the scanning mirror, to select matters of mirror and its support structures on the principle of consistent line expansion coefficient ; to ascertain type of moment electromotor by most rotating angle speed and most rotating moment which are required by loads in the period to take pictures, as well as by figuration size of electromotor ; to design retarder according as the electromotor parameters ; to design and optimize lightweighted mirror shapes, because the mirror is key part ; to design flexure support structure, to analyze static and dynamic characteristics of the support structure by name of patran program for validating desig n rationality ; to study function of the scanning mirror electric control system ; to test precision of the system, the results indicate the rationality of design of the scanning mirror system

    本文通過分析像移產生原因、研究像移補償原理，確定像移補償方案，並根據像移補償原理設計補償機構；分析與設計掃描反射鏡系統結構，根據材料線膨脹系數一致原則，選擇反射鏡及其背部支撐的材料；由掃描反射鏡在擺掃周期內的最大擺掃角速度確定力矩電機的額定轉速，根據負載力矩確定電機的額定轉距，綜合電機外型尺寸等因素，確定執行元件? ?電機的型號；根據所選電機的參數指標，設計1 ： 6速比的減速器；利用patran軟體對掃描反射鏡系統中的關鍵件? ?反射鏡進行輕量化設計與優化；設計反射鏡柔性支撐結構，並通過軟體分析支撐結構的力學特性，驗證反射鏡柔性支撐結構設計的合理性；從原理上研究掃描反射鏡控制系統功能；進行系統精度測試，測試結果表明掃描反射鏡系統設計的合理性。
  11. The experimental results are compared with the existing criterion and model so as to obtain the optimal overload protection model, viz. exponential heating and cooling equations, which can be used for protecting motors. based on the selected overload protection model, a thermal protector with single - chip is designed in this paper

    利用該裝置測試了被試樣機在不同負載率下的發熱和冷卻過程，並把實際測試結果同現有的電動機熱保護標準和熱過載保護模型作了對比，在分析和討論了各種標準和熱過載保護模型建模機理的基礎上，得出了最佳的、可供單片機式熱保護器使用的熱過載保護模型，即雙時間常數的指數發熱和冷卻方程。
  12. The inverted pwm changing electric current the technique is applied in the prototype model. the prototype model was tested and operated on spot, power factor could reach beyond 0. 95, the effect of following modulating voltage was better, the curve of factor of modulated voltage of exchanging systems changed following load rate was linear, the output of wave form was a flat and steady sinusoidal wave

    樣機採用了逆變式pwm變流技術，對其進行了現場測試與試運行，測試結果是電網側的功率因數可達0 . 95以上，跟蹤調壓效果良好，變流系統輸出調壓系數（ k ）隨負載率（ p ）的變化曲線基本滿足直線關系，輸出波形呈平滑穩定的正弦波。
  13. Through teat of relative vibration, center - line and center orbit of the shaft during starting - up and carrying load process, the abrasion mechanism, radial disturbance, loading status, and self - centering capability etc. of the the failured bearing have been analysed, and measures for preventing damage of bearing shoes being put forward

    摘要通過對機組起動及帶負荷過程中軸的相對振動、軸中心線、軸心軌跡的測試，對失效軸承的磨損機理、徑向擾動、承載狀況和軸承自調心能力等進行分析，提出了預防軸瓦損傷的措施。
  14. Frequently, load tests are run on a remote set of agent computers

    通常，負載測試是在一組遠程代理計算機上運行。
  15. So the equipment is schemed out to simulate the work - state of aepds, according to the in - out signals of every solid - state power controller ( sspc ) and the stochastic voltage and current of buses. the top - down design method is adopted in the design

    所以作者根據固態功率控制器輸入、輸出信號模擬多路負載，以及匯流條的電壓、電流等在飛機配電系統中的各種工作狀況，研製了「先進飛機配電終端自動測試裝置」 。
  16. Taking the ffc ? 23a disk mill as a specimen model, the rotation noise generated from the interaction between fixed claws distributed on the outer and inner circle of the fixed claw plate and the corresponding moving claws has been separated in an experimental study by the modern analytic method of acoustic. thereby, a conclusion that the principal component of rotation noise in disk mill comes from the interaction between the fixed claws on the outer circle and the corresponding moving claws has been reached. in accordance with the above, modified noise reduction design for the structural parameters such as the number of claws on the fixed claw plate, shape of claws and the relative positions of the claws arranged on the outer circle and inner circle has been carried out

    本文以ffc ? 23a型爪式粉碎機為樣機，利用現代聲學測試分析手段對其工作時定齒盤內、外圈齒與相應動齒作用產生的旋轉噪聲進行了試驗分離研究，從而得出了爪式粉碎機旋轉噪聲的主要成分源自外圈定齒與其相互作用的動齒產生的噪聲，並以此為基礎，對定齒盤的齒數、齒形以及內、外圈齒的相對排列位置等結構參數進行了降噪改進設計，通過對比性試驗與分析，獲得了旋轉噪聲與上述結構參數間的關系，並取得了負載6 . 7db （ a ）的良好降噪效果。
  17. The objective of the performance test was to submit, under various concurrent load conditions, a random selection of pre - defined ifx - encoded request messages and record the elapsed time to receive the anticipated ifx - encoded response

    性能測試的目標是，在各種並發負載條件下提交隨機選擇的、預先定義的、 ifx編碼的請求消息，並記錄接收到ifx編碼的響應的耗用時間（ elapsed time ） 。
  18. Through establishing three mathematics models including the movement equation of the mechanical and electrical transmission system, the control of the load and the sliding in stable status, direct - current - brake of ac motor, this paper ascertained the range of the frequency value of drive motor and the efficiency of transmission system, calculated the efficiency of load motor in stable status and the moment of load motor in braking. this paper completed the design of the mechanical part of inertia brake test platform and provides a tool for the measurement of the inertia brake parameters

    本文還通過建立慣性制動器試驗臺的包括機電傳動系統的運動方程、穩態運行時負載與轉差率控制、交流電動機直流制動在內的三個數學模型，確定驅動電機的頻率取值范圍和傳動系統的傳動效率，驗算慣性制動器穩態運行時負載電機軸功率和慣性制動器制動時負載電機軸力矩，完成慣性制動器試驗臺設計中的機械部分，為慣性制動器各參數的測量提供工具。
  19. After studying more deeply the fault tolerant algorithm and load balancing technology in redundant services, active load balancing is introduced into the redundant service system, and a novel fault - tolerant algorithm is built in this paper. under the conditions of guaranteeing the availability of redundant service system, the performance is effectively improved. the logic object model is based on corba and the prototype is implemented, additionally, system test results show the feasibility of the algorithm

    本文在較深入地研究了冗餘服務中的容錯演算法、負載平衡的基礎上，通過在冗餘服務中引入主動負載平衡機制，提出了一種行之有效的冗餘服務容錯演算法；該演算法一方面能夠滿足客戶請求對可用性的要求，另一方面有效地提高了系統的性能；基於corba分佈計算通信平臺，本文還構建了該演算法的對象模型，並在此基礎上實現了一個原型系統，通過實例測試驗證了該演算法的可行性。
  20. The part of the rig that is used to run tests and generate simulated load

    用於運行測試和生成模擬負載的遠程測試機組部分。
分享友人
分享到 Line

分享到臉書