負載電阻器 的英文怎麼說

中文拼音 [fùzǎidiànzǔqì]
負載電阻器 英文
loading resistor
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 負載 : [電學] load
  • 電阻 : （物質阻礙電流通過的性質） resistance; electric resistance （電路中兩點間在一定壓力下決定電流強度...
  1. In the experiment of varistor bleeder circuit, the successful load of equal voltage requires that the relation between load and varistor be correctly defined, so as to choose appropriafe experimental instrument

    摘要在變阻器分壓電路實驗中，要求負載得到均勻變化的電壓時，怎樣確定負載與變阻器之間的關系，以便在實驗中正確選擇實驗儀器。
  2. 1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %

    從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。
  3. Equipped with electronic controller fini tronic and preset for remote control for two or more compressors. it offers working pressure and oil mist separator tank inner pressure indication, separator filter clogging lashing alarm before overpressure e - stop, electric motor temperature control, maximum screw assembly temperature control, air temperature on pressure end indication, electric motor direction of rotation check, time to scheduled maintenance term, total operating hours and operating hours under load, alarm log of last five failure events

    並預設為丙臺以上空壓機聯機遠程控制，有工作壓力和油氣分離器罐內壓指示，分離器過濾器阻塞報警，電機溫控，螺桿總成溫控，壓力端空氣溫度指示，電機轉向檢查，維護周期油，油過濾器，空氣過濾器，分離器過濾器，總運行時間和負載運行時間，記錄上五個報警故障等。
  4. The system parameters are developed at the same time, and some universal conclusions on the theoretical analysis of pll are reached. then, we have carried on analysis and research to the theory of differential delay ring voltage controlled oscillator ( vco ). on this basis, a improved differential delay ring vco with more efficient loads is described. this circuit has been designed and implemented in 0. 35 m cmos technology

    本文還對差分延遲結構環形壓控振蕩器電路進行了深入的分析與研究，並提出了一種基於高質量電阻電路的主從差分延遲結構環形壓控振蕩器，其採用了一種新型的主從差分延遲結構，並用一個更有效、更穩定的負載電阻電路結構來替代vco設計常使用的單個mos管電阻結構，使其系統穩定性有了相應提高。
  5. The exportation resistance of a device work device with what link after loading the resistance s the certain connections for should satisfying, in order to prevent mount to load the appearance produce the obvious influence. with each other connect to say to electronics equipments, for example after signal connect the enlarger, ex - class to connect class, only behind first - degree importation resistance before larger than first - degree exportation resistance 5 - 10 times are above, can think the resistance to match good ; connect the box come saying, electronics tube the machine should choose to use with for the enlarger its output to carry the mark to call the resistance the box for, but transistor enlarger then have noing this restrict, can take officing why resistance of equal or approximate box

    一件器材的輸出阻抗和所連接的負載阻抗之間所應滿足的某種關系，以免接上負載后對器材本身的工作狀態產生明顯的影響。對電子設備互連來說，例如信號源連放大器，前級連后級，只要后一級的輸入阻抗大於前一級的輸出阻抗5 - 10倍以上，就可認為阻抗匹配良好對于放大器連接音箱來說，電子管機應選用與其輸出端標稱阻抗相等或接近的音箱，而晶體管放大器則無此限制，可以接任何阻抗的音箱。
  6. Combined with researches on propagation characteristics, the micro - current sensor for on - line pd monitoring is developed and the effects of coil number, stray capacitance and loading resistance on pass - band and sensitivity are also studied

    同時，結合傳播特性，研究了局部放電在線監測寬帶微電流傳感器，並就線圈匝數、雜散電容和負載電阻等對傳感器通頻帶、靈敏度等性能參數的影響進行了分析。
  7. Input capacity of time relay contact : 220v 30a

    輸出繼電器觸點容量： 220v 30a阻性負載
  8. Five different structures are described : standard transformer coupling, parafeed, resistively loaded stage capacitively coupled to the output transformer, tube ( valve ) based constant current source load capacitively coupled to the output transformer, and solid state ( mos fet ) constant current source load capacitively coupled to the output transformer

    我們將討論五種不同的方式：標準變壓器耦合；旁饋耦合；電阻性負載電容性耦合至輸出變壓器；膽恆流源負載電容性耦合至輸出變壓器；以及晶體管恆流源負載電容性耦合至輸出變壓器。
  9. In order to describe the actual working processes of dielectric barrier discharge ( dbd ) circuit, an analysis model of differential - difference equations was presented, based on the working modes of full bridge serial load resonant dbd circuit, which was adopted with phase shifting control

    摘要為描述介質阻擋放電型臭氧發生器電路的實際工作過程，在分析一種移相全橋脈寬調制下串聯負載諧振電源供電的臭氧發生器電路的基礎上，提出了採用微分差分方程來描述電路的工作過程，並給出了電路可能的工作軌跡。
  10. The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier

    本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。
  11. A pulldown resistor to the negative rail will allow the output to approach that rail ( provided the load impedance is high enough, or is also grounded to that rail ), but only slowly

    一個下拉電阻器將允許輸出迫近迫近該電源軌（所提供的負載阻抗足夠高，或負載也是接地的） ，但這樣速度較慢。
  12. The current in the dac ’ s output can drive the load, and the structure can save a buffer consisted of operational amplifier, so the structure can achieve high speed with no close - loop and feedback in this circuit

    該10位分段式電流舵型數模轉換器的輸出端可直接用電流輸出來驅動負載阻抗，省去運算放大器構成的輸出緩沖，整個電路中沒有形成閉環和反饋，因此這種電路結構可以達到很高的速度。
  13. The conventional connection circuit as the figure shows for two - wired transmitter : handhold terminal palm computer and external communication interface or mainframe communication circuit cannot directly bridges in the ends of power source. but may either meet on field ends a and b or meet on the ends of load resistance b and c. in the above - mentioned case, the circuit are supplied by power source

    對兩線制變送器來說，傳統的連接電路如圖所示：手持終端掌上電腦和外接通訊介面或主機通訊電路不能直接跨接在電源兩端，但既可接于現場兩端a ， b上，也可接在負載電阻兩端b ， c ，兩種情況下，電路都要通過電源來供電， hart規范允許負載電阻為2301100 。
  14. The preamplifier will drive a low impedance load without alteration in the signal, in fact it can be used as a current source driving a 0 impedance mixer junction without any distortion

    這個前級放大器能夠驅動一個低阻抗的負載而不會引起信號的變化，實際上它可以用作一個驅動零阻抗混合節點，而又不產生任何失真的電流源。
  15. The equilibrium current in 24 - pulse traction rectifier system is analyzed. the relation between critical load and resistance of traction rectifier transformer is discussed

    摘要分析了24脈波牽引整流系統中的均衡電流，討論了臨界負載與牽引整流變壓器阻抗參數的關系。
  16. In chart, ups is power source, lr is load resistance, tx is intelligent transmitter

    圖中， ups為電源， lr為負載電阻， tx為智能變送器。
  17. Load characteristics of dielectric barrier discharge type ozonizer

    介質阻擋放電型臭氧發生器負載特性研究
  18. Disadvantages : like the resistor load example, much higher voltage is required. an extra tube is needed. lower efficiency than the parafeed or transformer example

    缺點：和電阻負載一樣，高壓要求很高。需要增加膽管。比旁饋和變壓器負載效率更低。
  19. Clients may be required to provide appropriate loading resistors for the leak current test

    客戶或須提供適當負載的電阻器作漏電測試之用。
  20. A voltage regulator mainly composed of a comparator is added to the main conversion circuit to stabilize the output voltage. using tspice simulation software, it is obtained that the output voltage of the converter with this regulator has a reduced ripple of less than 0. 8 % and almost has nothing to do with the varied load resistance of more than 800

    為了穩定輸出電壓，在變換器主電路的基礎上增加了主要由比較器構成的穩壓環節，通過使用tspice對其模擬、優化設計后，得到的輸出電壓紋波小於0 . 8 ，並且在負載電阻? 800時，輸出電壓基本不隨負載電阻阻值的變化而變化。
分享友人
分享到 Line

分享到臉書