起重機門架 的英文怎麼說

中文拼音 [qǐzhòngjīménjià]
起重機門架 英文
portal gantry
  • 起 : 起Ⅰ動詞1 （站起; 坐起） rise; get up; stand up 2 （取出; 取走） draw out; remove; extract; pull 3...
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 機 : machineengine
  • 門 : Ⅰ名詞1 （房屋、車船等的出入口 ） entrance; exit; door; gate 2 （形狀或作用像門的東西） switch; va...
  • 架 : Ⅰ名詞1 （用來放置東西或支撐物體等的東西; 架子） frame; rack; shelf; stand 2 （毆打; 爭吵） fight;...
  • 起重 : jack up起重臂 jib loading boom; cargo boom; erector arm; jibboom; 起重車 carriage hoist; crane ca...
  1. The fifth chapter sums up the procedure of the crane outlook design, puts forward four projects on single - arm kickstand crane from it and compare them. by the help of autocad 2000, the article makes projection charts. the sixth chapter gives a conclusion on the research

    在前四章的基礎上第五章總結了門座起重機形態設計的程序，以此為依據，筆者做出了四套單臂架門座起重機形態設計的方案，並藉助autocad2000軟體作出了投影圖及效果圖，最後對四種方案進行了比較。
  2. , interpreations : overhead and gantry cranes top running bridge, single grinder, underhung hoist

    說明:高架起重機和龍門起重機
  3. The ansys, a kind of fea program, was used to build model of small carriage. the procedure of gantry beam bump with secondary beam of bridge was reappeared by running nonlinear calculation and loading program which was written by apdl program language. the closest deforming result was gotten, and the deforming of main beam, secondary beam and end beam and inner stress distribution status were calculated

    採用大型三維有限元軟體ansys對該起重機以及小車架等進行了建模、應用apdl語言編寫加載程序、進行非線性計算，再現龍門橫梁與起重機副梁碰撞過程，最後得到與實際變形結果最接近的一種狀態，得出起重機橋架主梁、副梁、端梁的變形以及其內部的應力分佈情況。
  4. Cranes and lifting appliances - classification - part 5 : overhead travelling and portal bridge cranes

    起重機和提升設備.分類.第5部分:移動式高架起重機和橋式龍門起重機
  5. Cranes - controls - layout and characteristics - part 5 : overhead travelling cranes and portal bridge cranes

    起重機.控制裝置.設計方案和特徵.第5部分:移動式高架起重機和橋式龍門起重機
  6. Interpretations : overhead and gantry cranes top running bridge, single or multiple girder, top running trolley hoist

    說明書:高架和龍門起重機說明
  7. Compare of service performance for two gantry mounting crane

    兩臺高架門座起重機的使用性能比較
  8. Ah type gantry crane

    Ah型低架門座起重機
  9. A great number of calculating results show that eeabs is effective and practicable. in addition, the method has been successfully applied into optimum design of two types of range - changing mechanism of gantry crane and the software systems of optimization design and analytical calculation of straight - arm gantry crane and ? ptimization design and analytical calculation of balance pulley compensation gantry crane ? has been compiled

    另外，作者還對基組結式消元法在兩種門座式起重機變幅機構優化設計中的應用做了成功的嘗試，並編制了「變幅補償直臂架門機的優化設計和分析計算」和「平衡滑輪式補償門機的優化設計和分析計算」軟體系統。
  10. Combining the design of portal crane luffing mechanism, this paper set up the math model independently and synthetically of the single boom system with compensating pulley and level - balancing weight. use genetic algorithms to optimize the model, the calculated results show as follows the genetic algorithms is effective and manipulable, the synthetically optimize is best than independently optimize. the optimization program of luffing mechanism was build, and this will be a useful tool in the design of crane

    結合門座起重機變幅機構的設計，建立了導向滑輪補償系統和杠桿? ?活對重臂架自重平衡系統獨立模型和綜合模型的未平衡力矩最小的優化問題，結合遺傳演算法對它進行了優化，結果證實了該演算法的有效性和可行性，表明了綜合優化比獨立優化更能提高優化的準確性。
分享友人
分享到 Line

分享到臉書