超壓密作用 的英文怎麼說

中文拼音 [chāozuòyòng]
超壓密作用 英文
overconsolidation
  • : Ⅰ動詞1 (越過; 高出) exceed; surpass; overtake 2 (在某個范圍以外; 不受限制) transcend; go beyo...
  • : 壓構詞成分。
  • : Ⅰ名詞1 (秘密) secret 2 [紡織] (密度) density 3 (姓氏) a surname Ⅱ形容詞1 (距離近; 空隙小)...
  • : Ⅰ動詞1 (使用) use; employ; apply 2 (多用於否定: 需要) need 3 (敬辭: 吃; 喝) eat; drink Ⅱ名...
  1. Aerostatic bearings have been applied widely on the ultra - precision in the aviation, aerospace and the main axes and the slide of the precision measuring instrument and inertial measuring apparatus because of high rotation accuracy, calm operation, low friction and long life - span etc. they can also be used in fields range from both high and low temperature to both high and low velocity, sometime even to environment full of radioelement

    氣體靜軸承回轉精度高、運轉平穩、摩擦小、使壽命長,可以在極高和極低的溫度、低到高的速度下,以及輻射環境中工,因此在航空、航天領域以及精測量和慣性測試設備上得到廣泛應
  2. Comparision of o - ring, un - cup, and che - cup seal used in single rod cylinder at ultra high pressure

    車氏三種封圈在缸中的應對比研究
  3. In this paper, nanosized al2o3 ceramic particles were chose as reinforcing phase. enhanced with ultrasonic wave the particles were covered with copper using method by electroless plating, the copper - matrix composite was developed by hot - press sintering process of the composite powder. the composition, microstructure, hardness, density and dry sliding wear property of the new material have been studied

    研究路線為:選納米級al _ 2o _ 3陶瓷顆粒為增強相,在聲波的環境中化學鍍的方法完成對納米al _ 2o _ 3陶瓷顆粒表面的金屬銅包覆,採燒結成型技術以復合粉末為原料制備成納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料,研究分析復合材料的成分、組織結構、硬度以及緻度,對試樣進行了干滑動摩擦磨損實驗。
  4. In this paper, the microstructure changes of polypropylene induced by a complex combination of shearing, compression, stretching and friction actions during single pan - milling or co - milling with iron, uhmwpe and waste tire rubber chips ( wtr ) were studied and the stress induced effects were revealed. the structure and morphological development of iron particulates and wtr during pan - milling and co - milling with polypropylene were also characterized. the properties of pp / fe, pp / wtr and pp / wtr / fe composites prepared through pan - milling techniques were investigated

    本文利磨盤型力化學反應器對被碾磨材料施加強大的剪切、環向應力、擠、拉伸和摩擦,研究聚丙烯碾磨和共碾磨粉碎過程微觀形態結構和性能的變化,以及聚合物在碾磨過程中呈現的力化學現象,並將其應拓展至金屬、橡膠等體系,研究碾磨粉碎在聚丙烯鐵微粉體的制備、高交聯度彈性材料廢舊輪胎橡膠( wtr )的微粉碎,以及pp fe , pp wtr材料的性能與碾磨的關系。
  5. The two - dimensional axisymmetric subsonic - transonic - supersonic flow in an experimental arcjet thruster is simulated numerically using flux vector splitting method. the profiles of density, velocity, temperature, pressure and mach number can be obtained by the computation. the computation grid and some computed results are given here. the test equipment such as power supply system, ignition system, propellant supply system, arcjet thruster, thrust measuring device and vacuum system are introduced briefly. some working phenomena of the arcjet are observed and discussed. three different kinds of instability appeared in the process of the experiments. except some important parameters are measured, it is found that the operating stability of argon is better than that of nitrogen

    對一實驗電弧加熱式發動機二維軸對稱亞跨音速流動進行了數值模擬,所採的方法是矢通量分裂演算法.通過計算可以得出度、速度、溫度、力和馬赫數的分佈.給出了計算所使的網格和一些計算結果.簡要介紹了實驗所使的設備,如電源系統、點火系統、推進劑供給系統、電弧加熱式發動機、推力測量裝置和真空系統.對所觀察到的一些工現象進行了討論.有三種不同的不穩定性出現于實驗過程.除了所測量的一些重要參數,通過實驗發現氬比氮工更穩定
  6. Abstract : the feature of positioning and compensating system based on piezodriven two - dimension micro displacement worktable was introduced in this paper firstly, then the performance of precision worktable was analyzed, the experimental results were given, finally the application of system in ultraprecision positioning and compensating was studied

    文摘:本文首先介紹了電驅動二維微動工臺定位補償系統的結構特點,然後對微動工臺的性能進行了分析,給出了性能實測結果,最後研究了系統在定位補償方面的應
  7. The soft - sealing gate valve should not be used on pipeline in which running pressure may be over the rated pressure

    封閘閥不應安裝在使力可能過其額定工力的管路上。
分享友人