跨導線性 的英文怎麼說

中文拼音 [kuàdǎoxiànxìng]
跨導線性 英文
translinear
  • 跨 : 動詞1 （抬起一隻腳向前或向左右邁） step; stride 2 （兩腿分在物體的兩邊坐著或立著） bestride; stra...
  • 導 : 動詞1. （引導） lead; guide 2. （傳導） transmit; conduct 3. （開導） instruct; teach; give guidance to
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 線性 : [數學] [物理學] linear; linearity線性代數 linear algebra; 線性方程 linear equation; 線性規劃 line...
  1. The factors limiting the frequency band of the wide - band amplifier are introduced. through analyzing the effects of the intrinsic parameters and parasitical on the frequency characteristics, a method of improving fr of mosfet by using short channel device and making mosfet work at the saturation region through raising vgs is put forward ; the effects of different kinds of circuit configurations on the frequency characteristics and the junction voltage on the voltage pattern circuit, current pattern circuit and frequency characteristics are analyzed. according to the linear theory of transconductance which is applied in the bit circuit, the current pattern amplifier circuit, current transfer circuit and output circuit which consist of mosfet and the wide - band amplifier composed of them are put forward

    介紹了限制寬帶放大器頻帶寬度的因素，通過分析mosfet的本徵參數、寄生參數對頻率特性的影響，提出了採用短溝器件、使mosfet工作在飽和區、抬高柵源電壓等提高mosfet特徵頻率的方法；分析了不同電路組態對放大器頻率特性的影響、節點電壓對電壓模電路、電流模電路頻率特性的不同影響，根據應用於雙極晶體管電路的跨導線性原理，提出了採用mosfet構成的電流模放大電路、電流傳輸電路、輸出電路以及由它們所組成的寬帶放大器，獲得了良好的頻率響應。
  2. The linear elastic slope deflection equations of gable portal frames when occur the side - sway and non - sway buckling are derived. the equations considere the rafter slope and the vertical uniform loading subjected on the rafter. the established equations of non - sway buckling can consider the effect of snap change effect of gable frame

    推導了山形門式剛架有側移失穩和無側移失穩的線彈性位移方程，方程考慮了斜梁傾角和斜樑上豎向均布荷載的影響;建立了能考慮山形門式剛架跨變效應的無側移失穩位移方程。
  3. The experiment procedure and analysis result about exteriorly extended end - plate connection with high strength bolt are introduced primarily ; each sample ' s dimension is given. the adding load equipment, measuring apparatus placed, measuring point established is detailed. adding load measure load and m - curve is produced ; the single span gabled frames horizontal displacement formula is deduced when the horizontal concentrated force is applied to it

    重點介紹了外伸端板高強螺栓連接的實驗過程及實驗分析結果，介紹了各組試件的形狀尺寸、加載裝置、測量儀器安放、測點的布置等；給出加載方式及測出的m -曲線；計算出試驗節點的初始剛度；推導水平集中力作用下單跨門式剛架考慮節點半剛性的側移計算公式。
  4. Research and design of honeywall in honeynet

    改善跨導放大器線性化方法的研究
  5. It shows that the method suggested in the paper is simple, applicable for engineering and has good precision. on the bases of the formulas deduced, and combining with relative test datas, it studies in the paper several factors influencing the bearing performance of the simple beams, such as shape of the external tendons, the equal moment segment length, span - to - depth ratio of the beam, valid initial prestress of the external tendons, area of the internal tension reinforcement, strength of the concrete, vertical distance between

    在公式推導的基礎上，結合相關試驗資料，研究了體外筋的形狀、等彎矩區長度、梁跨高比、有效張拉預應力、體內受拉筋配筋率、混凝土強度、錨固點到樑上邊緣在垂直方向上的距離、體外預應力筋水平段長度（雙折線型體外筋的情況）以及荷載類型等對體外預應力混凝土簡支梁受力性能的影響。
  6. The writer has been engaged in bridge design and construction for some years and doing attempting studies in mechanical characters of long span curved box - girder bridges in construction phase

    本人從事橋梁施工工作多年，在實際工作中逐漸摸索，對大跨度曲線箱梁橋施工階段的力學特徵進行了一些嘗試性的研究並得出了一些用以指導工程實踐的結論。
  7. Based on the historical space forecast data and corresponding actual data provided by a global semiconductor assembly and test company, the uncertainty of space planning was defined. during this analysis process, linear regression, grey prediction, neural network back propagation algorithm and confidence interval were applied, respectively, to define the uncertainty. compared with those methods, the confidence interval of historical space forecast error, calculated by mathematical statistics, was the reasonable method to define the space forecasting uncertainty

    本文從半導體工廠長期生產能力計劃的頂層即廠房生產面積的計劃展開，對一跨國半導體封裝測試公司提供的廠房生產面積的長期歷史預測數據以及對應的真實數據進行分析，採用線性回歸，灰預測，神經網路bp演算法，基於數理統計的置信區間的求解等方法分別定義廠房生產面積預測的不確定度，經多種方法的比較得出，基於數理統計方法求解出的生產面積歷史預測誤差置信區間能直觀清楚地標定不確定度。
  8. After introduction of the tranlinear loop principal, the bjt current controlled conveyor has been designed by using mixed tranlinear loop voltage follower. as for modern integrated circuit, the model of mos transistor, the active resistance and the current mirror integrated circuit formed by mos transistor are introduced. the cmos current controlled conveyor has been derived from mixed tranlinear loop cmos voltage follower based on weak inversion operation

    針對現代集成電路的工藝，本文對mos晶體管的工作原理進行了簡要的敘述，討論了有源電阻和電流鏡的實現方法，並利用mos晶體管的亞閾值特性組成混合跨導線性迴路完成對應的電壓跟隨器的設計，推導出了基於cmos技術的電流控制傳送器。
  9. In the chapter 4, the basic concept and characteristics about the current model circuit and transconductor ( gm ) are given. in order to optimize the performance of gmce, four linearization techniques and the design of consequently successful circuits are investigated and proposed. at last, the four linearization techniques are summarizes

    第四章討論了電流模式電路及跨導器的基本概念及性能特點，重點研究並給出了改善輸入級傳輸特性的線性程度並擴大線性范圍的四種方法，介紹在這方面比較成功的一些電路設計，總結了這四種方法的異同點。
  10. Chapter 2 deals with the fundamental theory and methods of bifurcation. the conditions giving rise to the static bifurcation are derived at first, then, the improved ls reduction method is studied and the centre manifold method is simplified

    第二章研究分岔的基本理論和方法，推導了一般一維非線性微分動力系統發生鞍?結分岔、叉式分岔和跨臨界分岔等基本靜態分岔的條件，改進和簡化了高維非線性微分動力系統的降維方法。
  11. This paper describes a reconstructive algorithm which is based on network theory for electrical capacitance tomography technic. there are twelve electrodes in the system. the permittivity distribution of flow with two components within a pipeline is reconstructed. assume the permittivity distribution of the region to be reconstructed. then whole measured area is discretized into a network composed of capacitance. the measurement circuit which contains a pair of source electrode and detecting electrode is taken as a four - terminal network. the across admittance of the four - teminal network is proportional to the capacitance between the source electrode and the detecting electrode. modify the distribution of the permittivity according to the difference between the calculated capacitance and measured capacitance. the experimental results show that this algorithm is effective and can coverge

    本文描述了一種用於兩種成份的流體成像的12電極電容層析成像新方法.該方法基於電路的網路理論，首先對重建區域假定一個介電率分佈，用電容網路作為離散化模型，將每一個源電極和探測電極對組成的測量電路看作一個四端網路，該四端網路的跨導與源電極和探測電極之間的電容值是線性關系，這個電容值和測量得到的電容值之間存在誤差，根據這個誤差對修正介電率分佈.通過對不同介質分佈作的模擬實驗結果，證實了該演算法是有效的，收斂的
  12. Specifically analysed and presented the common - mode differential input stage, linear transconductance control circuit of input stage, current sum circuit, floating ab - class control output stage, the bias circuit of op amps and the bandgap reference current source circuit

    具體對運放的共模差分輸入級、輸入級線性跨導控制電路、電流和電路、浮動ab類輸出級電路、運放的偏置電路和帶隙參考電流源電路進行分析設計。
  13. This converter is thermally protected and current limited, protecting the load and regulator during fault conditions. in the circuit design chapter, the basic charge pump operation principle and equivalent circuit model are given first. then two control modes, pulse skip mode and linear mode, are analyzed

    在電路設計中，首先分析了跨周期調制的電荷泵dc / dc轉換電路的基本原理，然後推導出電荷泵等效模型，以此為理論依據分析了電荷泵的兩種控制模式:線性調制模式和跳周期調制模式。
  14. Also discussed the methods on how to realize the cwt both in time - domain and frequency - domain and how to design the gm - c bandpass filter used in realization of cwt. in order to optimize the performance of gm - c filter, linearization techniques are investigated and proposed. due to process variation and parasitics, an automatic tuning is designed for center frequency / 0 and quality factor q also, in this thesis, 16 - channel analogue cmos cwt circuit has been realized

    論文圍繞連續小波變換的模擬電路實現這一熱點問題，討論了連續小波變換的時域和頻域實現方法；具體分析了并行結構與串列結構的優缺點；研究了頻域法中的跨導-電容帶通濾波器的設計；給出了改善跨導輸入級傳輸特性的線性程度並擴大線性范圍的具體方法；設計了片內自校正（可調諧）環節使濾波器參數自動調整到設計標準值；最後給出了16通道濾波器組實現小波變換的方法。
  15. In the fourth chapter, a fourth - order chebyshev low - pass filter employs new low voltage, highly linear, wide inputting range transconductor is proposed, then we presents a new circuit to tune gm value of transconductor accurately, which employs a new switched - capacitor circuit to change the bias current of transconductor, a third order elliptical function low - pass filter with accurate tunable frequency has been designed using transconductor that is not only with voltage common - mode negative feedback, but also with varying bias - triode transistors which can improve the linearity of this circuit

    第四章：提出了一種新的低電壓、高線性度、寬輸入范圍跨導，並由此設計實現了四階切比雪夫（ chebyshev ）低通濾波器，接著提出了一種寬輸入范圍且具有電壓共模負反饋的全差分跨導，並採用一種新的開關電容電路實現跨導值gm精確可調，從而可以設計得到高性能具有精確截止頻率的跨導-電容三階橢圓函數濾波器。
  16. The comparison showed that : ( l ) farassat 1a formula is the simplest one and work well for the subsonic rotor. ( 2 ) both kirchhoff formula and k - fwh formula can predict the nonlinear noise generated by transonic rotor ; ( 3 ) when the surface is not positioned in the linear region, kirchhoff approach for rotating integration surface could lead to substantial error, but k - fwh formula can still work well

    數值研究表明： farassat1a公式在預測線性噪聲方面簡單有效，適用於亞音速旋翼的噪聲預測； kirchhoff公式和k - fwh公式均能夠預測跨音速旋翼聲場，並且具有較高的精度；當聲源面位於流動非線性時， kirchhoff公式會導致很大的計算誤差，而k - fwh公式不存在這樣的問題。
  17. This paper studies the key techniques involved in the construction of the deep water foundations, long - span prestressed concrete continuous rigid - framed girders and long - span concrete - filled steel tube arches of yichang changjiang river bridge on the newly built yichang - wanzhou railway, and also provides solutions to the possible problems thereof, which may be of certain guiding roles to the practical construction

    摘要對新建鐵路宜昌至萬州線宜昌長江大橋深水基礎、大跨度混凝土連續剛構梁、大跨度鋼管混凝土拱等施工過程中遇到的關鍵技術問題進行了研究，並對各個問題提出了解決方案，對實施性施工有一定的指導意義。
  18. As a monumental project of the large - scale development in the west, it covers nine provinces and municipalities along its gas pipelines. consequently, chang zhou factory of coke and chemicals is confronted by the challenges of changing market, government subsidy reduction and natural gas introduction. how to extricate from the predicament and maintain sustained growth is a primary problem, which the coke industry and particularly the coke factories affected by the project, should ponder over

    西氣東輸作為西部大開發的標志性工程；在橫跨東西部九省一市的漫長管線上已全面啟動，與之相關的常州焦化廠正面臨市場變化帶來的沖擊、政府補貼的削減與天然氣導入的威脅；如何在新的形勢下，擺脫困境獲得企業的長效發展，是焦化行業尤其是受西氣東輸沖擊的各焦化廠正在思考和摸索的首要問題。
分享友人
分享到 Line

分享到臉書