軸向匹配 的英文怎麼說

中文拼音 [zhóuxiàngpīpèi]
軸向匹配 英文
axis match
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 匹 : Ⅰ動詞（比得上; 相當; 相配） be equal to; be a match for Ⅱ形容詞（單獨） lone Ⅲ量詞1. （用於馬、騾等） 2. （用於整卷的綢或布）
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 匹配 : 1. [書面語] （婚姻配合） mate; marry 2. [電學] matching
  1. Minyu low head screens are horizontal screens to which an extremely powerful linear vibrating motion is imparted by two unbalanced eccentric shafts and weights. the screens ecciciently handle a large amount of materials. resist clogging, and suit best for classifying small granules. some features of the mlh screen are as follws

    振動篩-振動篩是利用電動激振器或偏心軸偏心塊作為振動源，使物料在振動篩篩網上被拋起，振動篩同時向前作直線運動或做橢圓運動及復雜運動，以合理匹配的振動篩篩網達到篩分目的。
  2. With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress

    研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。
  3. In this paper, the equilibrium equation of liquid bulge forming small tangential round corner is deduced for the complicated shape tube - type blank, the function equation between forming stress parameters are and the small corner are obtained ; the forming mechanism of the small tangential corner is studied, the matching relation between liquid bulging pressure and axial thrust is given, the optimal liquid bulging force parameters are determined

    摘要本文推導出復雜形狀管類件復合液壓脹形時環向小圓角成形的平衡方程，得出了成形應力與環向圓角半徑的解析關系；研究了環向小圓角成形機理，確定了液體脹形壓力與軸向推力的匹配關系以及最佳的成形力參量。
  4. This direction finding algorithm may resolve uncorrelated monochromatic sources, but it assumes that all signal frequencies are distinct. it requires no a priori knowledge of the signals " frequencies, suffers no frequency - doa ambiguity, and pairs automatically the x - axis direction cosines with the y - axis direction cosines

    該演算法用單矢量水聽器，在無需知道信號先驗信息的條件下，可以實現對多個不相關信號的方位角估計，並且不受頻率模糊度的影響，自動匹配x軸、 y軸的方向餘弦。
  5. Considering the loading stability, it is necessary to switch the matching relation between internal pressure and axial force to the matching relation between internal pressure and axial compressive displacement

    出於對控制實現的考慮，有必要將內壓軸壓的匹配關系轉換為內壓軸向壓縮位移的匹配關系。
分享友人
分享到 Line

分享到臉書