軸向對稱流動 的英文怎麼說

中文拼音 [zhóuxiàngduìchènliúdòng]
軸向對稱流動 英文
axial symmetric flow
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 稱 : 稱動詞（適合; 相當） fit; match; suit
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 流動 : 1. （液體或氣體移動） flow; run; circulate 2. （經常變換位置） going from place to place; on the move; mobile
  1. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  2. Abstract : approximate methods for calculating aerodynamic heating rates on space shuttles are discussed. various methods are given for predicting the heating rate at axisymmetric stagnation points, general three dimensional stagnationpoints and the leading edge stagnation point of wings. numerous laminar and turbulent heating techniques for flat plates and cones are analyzed and compared. a brief review of some methods is presented to predict heating rate for winward centerline and lateral direction off the symmetry plane. the results show that the methods are simpler and can guarantee enought precision for predicting aerodynamic heating environment of space shuttles

    文摘:介紹了國內外預測航天飛機氣動加熱的工程計算方法.給出了軸對稱、非軸對稱和機翼前緣等各種外形駐點熱流密度的計算，分析和比較了平板、錐體的層流和湍流熱流密度計算的各種方法，概述了航天飛機迎風面中心線和離開中心線橫向熱流密度的計算.計算結果表明，本文方法用在航天飛機氣動熱環境初步設計中比較簡單並且有足夠精度
  3. The main results can be summarized as the folio wings : in the certain parameter range, the circular shearing basic flow might be able to axisymmetrize the one - wave asymmetric structure of a typhoon and also to transfer the perturbation vorticity in the outer region inwards

    主要結果可以歸納如下：在一定的參數范圍，圓形切變基流可以使初始一波非對稱結構軸對稱化，也可以使外區的擾動渦量向內傳播。
分享友人
分享到 Line

分享到臉書