軸向強度 的英文怎麼說

中文拼音 [zhóuxiàngqiángdù]
軸向強度 英文
axial strength
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. With carbureted high - strength good - quality alloy, the series has the feature of high - efficiency and long life - span, high permissible axial and radial loads, low noise, high reliability and compact structure and so on configuration modality

    採用高強度優質合金鋼滲碳游淬火，具有高效率高壽命輪及高許用軸向，徑向載荷，運行噪音低，可靠性高，結構緊湊等優點。
  2. Specially, the axial tensile strength of the interface of the new and old concrete has reached above 2. 40mpa, greatly surpassing the preconcert goal ( > 1. 0mpa ), and its flexural strength also above 5. 80mpa, having surpassed the preconcert target and the standard request ( 4. 50mpa ). ( 2 ) after hardening 4h and 8h the compressive strength of the patched concrete is bigger than 20 mpa, which can satisfy the request of fast patching. ( 3 ) the ych color material, which is mixed into rapid sulfoaluminate cement - concrete patching material, can take better effect and avoid chromatism on the appearance of new - old concrete

    特別是新老混凝土界面的軸向抗拉強度已達2 . 40mpa以上，大大超過原定目標（大於1 . 0mpa ） ，其界面抗折強度也在5 . 80mpa以上，也已超過原定指標及規范要求（大於或等於4 . 50mpa ） ; （ 2 ）修補混凝土硬化后4h 、 8h抗壓強度大於20mpa ，能滿足快速修補的要求; （ 3 ）在快硬硫鋁酸鹽水泥混凝土修補材料中摻入自配的ych調色材料，能較好地起到調色作用，避免新老混凝土表面色差。
  3. It is found that the anomalous sea ice area over the southwest part of the sea of okhotsk, together with the associated northern pacific sst anomaly, can exert crucial influence on the variability in the vigor and nw - se extension ( contraction ) of the pacific storm track, while the sea ice area anomalies over the area of northeastern part of the sea of okhotsk and the gulf of shelikhow, together with its associated north pacific ssta, mainly impact the strength and south - north movement of the storm track

    結果發現：冬季鄂霍次克海西南部海區海冰面積異常與北大平洋海溫異常共同作用對北大平洋風暴軸在西北東南方向的伸縮及強度的年際變化有重要影響；鄂霍次克海東北部及舍列霍夫海海區海冰面積異常與海溫異常的共同作用主要影響風暴軸的南北位移和強弱。
  4. 4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity

    結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。
  5. This article gives the subsistent ability and the analysis result of intensity after repair in the open field airplane composite material structure by research the intensity, rigid and repair problem under a axis compress loads on a typical three stiffened composite laminate which has a penetrability crack ( a scatter damage ) by a shrapnel

    本文通過飛機典型復合材料三加筋層壓板結構在被彈片劃開一穿透性切口（離散源損傷）后，在軸向壓縮載荷作用下所產生的強度、剛度以及修理問題展開了技術研究及探討，給出軍機復合材料加筋板在彈擊後生存力以及外場修理后強度恢復分析結果。
  6. 2. the influence of different axis linear acceleration on coriolis illusion to observe the effect of different axis ( x x y axis ) linear acceleration on coriolis illusion on gl - 2000 a

    16c加s們1起的科里奧利錯覺形態、持續時間、強度進行了比較，結果發現：同無線加速度作用相比，在x軸向線加速度為0二7gx及y軸向線加速度為0
  7. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  8. Based on the strength design theory and the practical stress features of the drums and on the phenomenon that the drums produce the circumference stress along the drums under the binding force of the wire ropes and the bending stress along the axis, the paper proposes the fourth strength theory as the basis for the drum strength design

    利用強度設計理論，結合捲筒實際受力特點，針對捲筒體在鋼絲繩緊箍外壓作用下產生沿捲筒徑向、周向應力和軸向局部彎曲應力的情況，提出了以第四強度理論為依據的捲筒強度設計準則。
  9. Through developing the comprehensive experiment device with large - scale drum strength and stability, the stress - measuring experiments of various wall thickness of the normal drums of the cranes were performed. the law that the stress of the drums along the circumference and along the axis changes with the load increase of the wire ropes was studies for the first time

    通過研製全比尺大型捲筒強度、穩定性綜合試驗裝置，對起重機常用規格的捲筒進行了各種壁厚條件下的應力測量試驗，首次對捲筒體周向和軸向應力隨鋼絲繩逐步加載過程變化的規律進行了研究，發現最大應力產生在鋼絲繩繞過后3 ~ 5圈截面處，該現象與理論分析結果也是符合的。
  10. Using non - saturable polyester resin as its basal masal and unidirectional fiberglass woven fabrics as its skel eton, the frp pole is taken shape by ce - ntrifugal kr twine forming process and has high axial strength and its content if fiberglass is over 50 %. the frp light pole

    Frp燈桿系採用不飽和聚酯樹脂為基材，以單向布為主的玻璃纖維織物為骨架，採用離必成型工藝或發纖維骨架通過纏繞成型工藝製作而成，玻璃纖維含量在家50 %以上，軸向強度很高。
  11. At last, the finite element method, the strength reduction method and limit equilibrium method, nature slopes and excavation slopes, lateral stress unloading model and axial loading model are analyzed and discussed relatively

    最後，就有限元法、強度折減法和極限平衡法，自然邊坡與挖方邊坡，圍壓卸荷應力路徑模型分析與軸向加荷應力路徑模型分析進行了比較討論。
  12. The mechanics properties of two type of the lwts mixed with different foamed plastic beads are researched by the uniaxial compression test, the isotropic compression test and the triaxial compression test

    本文對添加不同種類泡沫塑料顆粒的輕質混合土試樣進行了無側限抗壓強度試驗、等向壓縮試驗及三軸剪切試驗。
  13. When draw down ratio was greater than 1, the dope thread in the air gap was axially drawn with the rising of orientation degree so the fiber tenacity was strengthened

    在噴頭拉伸比大於1的情況下，原液細流在空氣層中得到軸向拉伸，加大了初生纖維的取向度，所以纖維強度得到加強。
  14. In this part, it is also found that the equivalent prismatic column, which is obtained based on the equal elastic critical load as the non - prismatic member, is not actually equivalent to the tapered column in inelastic stability, and the latter has higher load carrying capacity. finally, the behavior of tapered beam - column acted by combined axial load and transverse load has been investigated. a bending - thrust interaction curve is established which is similar to the ones for the design of prismatic members

    三是研究了楔形變截面懸臂構件在大端固定，小端同時承受橫向及軸向荷載共同作用下的強度和彎矩平面內的穩定，同時參考等截面構件的設計公式，得到了用大端截面來表示的軸力p與彎矩m的之間的相關關系。
  15. Yingxian ancient wooden pagoda is a flat - form tall building, which was formed by the superposition of monolayer temples. the height of 67. 31 meters made it encountered two unprecedented puzzles : firstly, with the height increased whopping, wind resisting and aseismatic capability become the main question of the whole structure ; secondly, because of the weight increased unconventionally, members of the lower 1 ~ 3 floors hold overloading perpendicular to grain and they brought large vertical deformation

    相對於一般殿堂結構，高度和自重的成倍增加，使木塔遇到前所未有的兩項難題:其一是因自重增加，使承受上層柱軸向荷載的梁（普拍枋和梁? ）橫紋局壓應力成倍地超過設計強度而產生嚴重的壓縮變形甚至劈裂，導致木塔整體豎向變位。
  16. Because the field caused by the eddy - current transducer in the dissertation is not only axially symmetrical, but also plane symmetrical, there is no normal component of the electrical field strength and we cannot apply the condition en = 0 to solve such a problem

    由於本文中的渦流傳感器模型，其電磁場不僅是軸對稱場，而且還是平面對稱場，不含有電場強度的法向分量，所以無法利用邊界條件e _ n = 0來求解。
  17. With the different tripping annulus at the inlet, a new method of the distance definition from the wall was used to measure 35 mean velocity profiles on seven sections in the pipe length x / d = 125. 2

    採用新的離壁距離標定方法，在入口處設有改變擾動強度擋環的條件下，利用熱線儀在管長x d約為125的范圍內完成了七個不同管流截面上的35個軸線方向速度分佈的測量工作。
  18. The rigid ring strengthened stories may be set along the frame. so the relations between the tube and frame will be stronger. the overturn moment of the inner tube will be reduced by the axial stiff of circumjacent frame column, and the horizontal stiffness of the whole building will be enhanced

    在核心筒與外圍框架之間設置剛度較大的水平伸臂構件或必要時沿外圍框架設置剛度較大的周邊環帶加強層，可以加強內芯與周邊框架柱的聯系，充分利用周邊框架柱的軸向剛度而形成的反彎矩來減少內筒體的傾覆力矩，從而達到減少結構在水平和在以增強整個結構的抗側力剛度。
  19. The axial velocity, fluctuation velocity, the turbulence intensity, and transverse velocity of the fine particle were studied

    研究了管道中近壁區顆粒的軸向速度、湍流強度和徑向速度。
  20. The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented

    採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。
分享友人
分享到 Line

分享到臉書