軸向通孔 的英文怎麼說
中文拼音 [zhóuxiàngtōngkǒng]
軸向通孔
英文
axially extending bore-
In airborne synthetic aperture radar ( sar ), antenna stabilization platform is used to isolate antenna pointing, which is stabilized through controlling the platform axis ' rotation, from the vehicle ' s varying attitude and dynamical vibration
摘要機載合成孔徑雷達中,天線穩定平臺用於隔離載機的姿態變化和機械振動對天線指向的影響,並通過伺服系統控制平臺支承軸的轉動穩定波束指向。Though, the lateral resolution of cm has been enhanced to be 1. 4 times of that of a conventional optical microscope under the same aperture focus ratio, it is still two orders of magnitude lower than the axial resolution of itself. so, it is urgent to further improve the lateral resolution of cm
然而,盡管共焦顯微鏡的橫向分辨力已提高到相同孔焦比的普通光學顯微鏡的1 . 4倍,但與其本身的軸向分辨力相比,橫向分辨力仍低2個數量級,因此進一步改善共焦顯微鏡橫向分辨力的研究顯得尤為迫切。It was found that there are lower pressure drop and better distribution in the radically variable cell diameter converter and the inlet loss of catalytic converter may be neglected when the velocity in cell passage is low
結果發現,三效催化器微元通道孔徑沿徑向的不同組合可以達到既不增加壓降、流速分佈又均勻的效果,而且在所計算的軸對稱三效催化器結構中,在通常的流量范圍內其進口損失可以忽略。Laboratory glassware ; double bore stopcocks with tail
實驗室玻璃儀器.帶軸向排出孔的三通錐形旋塞This machine is a kind of radial riveting machine, the machine adopted the advanced radial technology, and its movement path likes the 11 pieces of plum blossom s shape, and using the screw pole to ascend and descend the work bench the head part is fixed, and the t - slot of bench can fix the clamping apparatus available, the center hole of bench and axis are coaxial, the one - way adjusting valve of liquid current is effectively controlled riveting speed
Jm12 - c是液壓類中重型徑向鉚接機,除應用有第五代徑向鉚接技術外,該機加長了鉚接行程,該項參數由普通機型的30mm加至60mm ,可滿足長行程深孔內鉚釘鉚接的要求。工作臺,並具有夾具梯形槽,工作臺中心孔徑與主軸軸線同軸,可用於夾具定位。氣路加裝雙向調節閥,有效控制鉚接速度。By analyzing the influence of hemisphere pits with different dimension and ellipsoid pits with different aspect ratio on stress and strain distribution of lap joint, the possible propagation of fatigue crack was discussed, and the effects of localized pitting corrosion on the structural integrity of lap joints were discussed
通過分析不同尺寸的半球形蝕坑和不同長短半軸比值的半橢球形蝕孔應力應變分佈的影響,探討搭接件疲勞裂紋的可能擴展方向,討論局部孔蝕對搭接件結構完整性的影響。The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented
採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論;採用不同的熱輻射分析策略,對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析,解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題,提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路,給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。Through studying the cptu chamber test with the soil as a medium in door, according to the stress which generated in the course of probe penetrating, include axial additional stress and radial additional stress, measured by subminiature pressure cells which buried in the soil. this paper analyzed the rule of variation of axial and radial additional stresses, and compared with each other
摘要通過以粘土為介質的孔壓靜探( cptu )模型槽試驗研究,根據埋置在土中的微型土壓力盒在貫入過程中所則到的土應力(軸向附加應力和徑向附加應力) ,分別分析了軸向和徑向附加應力的變化規律,並進行了比較。分享友人