軸對準誤差 的英文怎麼說
中文拼音 [zhóuduìzhǔnwùchā]
軸對準誤差
英文
axis misalignment- 軸 : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
- 對 : Ⅰ動詞1 (回答) answer; reply 2 (對待; 對付) treat; cope with; counter 3 (朝; 向; 面對) be tr...
- 準 : Ⅰ名詞1 (標準) standard; guideline; criterion; norm 2 (目標) aim; target Ⅱ動詞1 (依據; 依照)...
- 誤 : Ⅰ名詞(錯誤) mistake; error Ⅱ動詞1 (弄錯) mistake; misunderstand 2 (耽誤) miss 3 (使受損害...
- 差 : 差Ⅰ名詞1 (不相同; 不相合) difference; dissimilarity 2 (差錯) mistake 3 [數學] (差數) differ...
- 誤差 : error
-
Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析,並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算,最後對誤差進行合成。Axis - misalignment error compensation method based on optical alignment for a multi - sensor assembly
基於光對準的多傳感器軸裝配誤差補償技術The error has an effect on image registration and synthesizing. for synthesizing high resolution image, the angles between channels need be measured, then calibration of eut in orbit will be carried out
這些誤差必然會影響圖像配準、合成等。為了合成高解析度的圖像,需要測出各通道軸向夾角,對其在軌校準,從而減小觀測上的誤差。The author first explains that large - scale measurement device is one of the most basic measuring methods of obtaining external trajectory data and flight status. lt is pointed out that the accurateness of the main - item axis system deviation correction ( including vertical, level and collimating axis deviation ) of large - scale measurement device error is of critical importance to the precison of measuring device ' s surveying angles. to improve its precison, the influence of axis system deviation on surveying angles must be corrected
首先說明了在現代航天靶場中,大型測量設備是獲取外彈道數據和飛行狀態的最基本的測量手段之一,指出大型測量設備測量系統誤差的主項軸系偏差(包括垂直軸偏差、水平軸偏差和照準軸偏差)改正的精確與否直接關繫到測量設備的測角精度,因此要提高測量設備的測角精度,必須對軸系偏差對測量角的影響進行改正。分享友人