軸對稱體型 的英文怎麼說
中文拼音 [zhóuduìchèntǐxíng]
軸對稱體型
英文
axisymmetric body form-
Abstract : reviewed are five methods for the analysis of the penetration of jacked - in piles, namely, cavity expansion method, strain path method finite element method, slip line method and calibration model test. after analysis, it is pointed out that it is more rational to adopt sub - statical spatial axisy numerical formulas based on traditional plane - strain cavity expansion method in the analysis. after spatial closed - form solutions are obtained for soil movements, stresses and initial excessive pore pressures generated durihy pile penetration are found out. it is suggested that finite element analysis together with centrifugal model test be used in verifying the results
文摘:在分析飽和粘土中靜壓樁的貫入機理的基礎上，對靜壓樁沉樁分析的圓孔擴張理論、應變路徑法、有限元分析、滑移線理論和模型槽試驗等五種方法逐一進行評述，並提出在傳統的平面圓孔擴張理論基礎上加以改進，採用準靜態空間軸對稱方程組對靜壓樁貫入過程進行模擬，從而得出土體位移、應力、初始超孔壓的空間解析解，同時採用有限元分析、模型槽試驗相互印證的研究方法According to the working modes of mr devices, combining the ohm ' s law of magnetic circuit and the design theory of non - steady magnetic circuit, magnetic structures of the automotive damper have been worked out. to emulate the performance of conventional shock absorber, two automotive mr dampers were designed and fabricated at chongqing university. an applied magnetic field increase the yield stress of mr fluids in flow annular passages, which alters the velocity profile of mr fluid in the passages and raise the pressure gradient between low cavity and high one at some given flow rates
根據磁流變阻尼器工作模式，利用磁路中的歐姆定律和動態磁路設計原理，結合汽車懸架的技術要求和結構特點，提出了基於剪切模式和流動模式共同作用（混合工作模式）的汽車磁流變阻尼器設計原理，討論了阻尼器動態磁路設計中的若干技術問題；根據流體力學navier - stokes方程，分別利用newton流體特性和bingham流體特性，推導了基於平板模型和軸對稱模型的流變學方程，得出了阻尼器阻尼力的計算方法。Through the analyzes of electromagnetic system of a axial symmetry by the method of electromagnetic vector potential, an eddy current field math model is build by triangle cell, this article has researched the effect of power frequency to eddy current density, penetration depth and the skin effect
本文以電磁場矢量位有限元法為基礎對二維軸對稱場的磁場強度、渦流密度進行了計算求解，採用三角形單元和六面體單元建立了渦流場數學模型，研究了電源頻率對渦流密度、透入深度及集膚效應等場量的作用影響。The paper establishes mathematics model of electromagnetic heating system of eddy current field and temperature field, and gives corresponding discrete format with elements as eight nodes, hexahedron equal cell, through calculating eddy - current field to gain the internal heat source that the temperature field needed, to use discrete method to solve the problem of induction - heating part ' s temperature field by axial symmetrical electromagnetic, and then to analyze the characteristic of instantaneous temperature field
本文建立了電磁加熱系統的渦流場和溫度場間接耦合的數學模型，分析了不同頻率下渦流和溫度的分佈情況，並以八節點六面體等參元為例給出了渦流場對應的離散格式，通過計算渦流場獲得溫度場所需要的內熱源強度，加熱部件的溫度場以軸對稱格式進行離散求解，並對瞬態溫度場有限單元法的求解特點進行了分析。The work theories of electromagnetic brake and its existing problems are analysed. a kind of new non - axis - symmetry electromagnet structure is also described in the text
摘要分析了電磁製動器的工作原理，以及其存在的問題，提出了一種新型非軸對稱電磁體結構。The secondly, based upon the laboratory soil tests, definite the parameter of the kondner model and the loess compaction model, using fortran power station to compile the finite element programmed of axial symmetry. through trial calculate with the different squeeze stress and different poisson ratio, got some laws of stress of soil surrounding pile and judged the result of compaction pile. the result of the calculation and analysis and valuable to designer and builder
同時通過室內試驗確定了特定區域黃土的鄧肯-張模型參數和黃土擠密模型，採用fortranpowerstation ，按軸對稱問題編制了存限元程序，通過採用不同的擠壓力和不同的泊松比的程序試算，得到了一些樁周土體的應力變化規律，並對擠密樁破壞半徑內的土體擠密效果進行了判定，計算與分析結果可供設計施工人員參考。The numerical simulation was made on this kind of energy dissipator by using the k - s turbulence model, the full - field distribution of the time - averaged parameter and the turbulence parameter are described in detail, the calculated time - averaged pressure has good agreement with the experimental results, some advice can be provided for the further study and application in this thesis, especially the calculated results can be used to check the lowest time - averaged pressure
本文對洞塞式消能工採用軸對稱的k -模型進行了數值模擬，數值模擬結果詳細地描述了時均流參數和紊動參數的全場分佈，計算所得的壁面時均壓力結果與實驗結果相吻合，獲得了實體試驗難以獲得的流動特徵。可供這種消能工的進一步研究和應用提供參考，特別是可用於檢驗壓力最低點的大小。According to the physical model, a mathematical model and computational method were proposed. an axially symmetric transient thermal conduction equation was put forward, which included material pyrolysis, pyrolysis gas flow and chemical reaction in charred layer. chemical reaction was controlled by chemical dynamics, and the reaction rate was computed using arrhenious equation
針對物理模型提出了相應的數學模型和數值計算方法，在材料內部建立了二維軸對稱的非穩態導熱控制方程，其中加入了材料熱解、熱解氣體流動以及炭化層內的化學反應等因素的影響，化學反應由化學動力學控制，通過arrhenius公式確定其反應速率。Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure
試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。On the assumption of ignoring the distortion of thickness, this paper determines the rough shape by the geometric modeling method of equal area developing using mixed mesh cell of triangle and quadrangle for the first time, presents the equal area developing arithmetic of quadrangle - triangle. on the virtual geometric symmetry axis, we puts forward the method of determining the developed coordinate of the point on the base band in the development of using regular quadrangle cell, determines the developed shape of internal structure in plane utilizing point - to - point mapping theory. furthermore, we realize the approximate developing of undeveloped - irregular boundary surface using a few triangle cells
本文結合型號研製中小曲率機翼整體壁板類零件坯料展開課題，基於板料厚向變形忽略不計的先驗假設，首創混合四邊形-三角形網格等面積展開的幾何模擬法確定壁板類零件毛坯外形，給出了混合四邊形-三角形網格等面積展開演算法；提出了虛擬分割線的概念，採用虛擬幾何對稱軸，給出了規整四邊形單元展開基帶上結點的計算方法；採用映射原理和求交演算法確定了壁板內部結構信息的展開定位。A technology for designing a dishing axial - symmetric unmanned helicopter that based on a coaxial rotor system shrouded by a toroidal shell is studied in this thesis
本文研究碟形軸對稱無人直升機的總體設計技術，這種特型的無人直升機是將一副共軸式旋翼置於涵道中，外形為碟狀。After the study of model of the supercavitation for axisymmetricbody, a formula is established to calculate the simulated supercavity shape
本文在深入研究了軸對稱回轉體超空泡數學模型的基礎上，建立了用於模擬的超空泡外形計算公式。In this thesis, a 2 - d axial symmetric n - s equation was solved by using steger - warming flux splitting, muscl, b - l model and finite volume method to simulate an experiment, which was to observe explosion phenomenon
本文用steger - warming分裂和b - l湍流模型的有限體積演算法求解二維軸對稱navier - stokes方程，數值模擬了錐形激波管中爆炸波運動和爆炸波正壓和負壓脈沖。In the dissertation body - of - revolution finite - difference time - domain method ( bor fdtd ) is employed as the theory mode for the analysis of axially symmetric subwavelength diffractive microlens
論文中將旋轉體時域有限差分法（ borfdfd ）作為分析具有軸對稱結構的亞波長衍射微透鏡的理論模型。Modeling soil as a three - dimensional axisymmetric continuum and taking its 3d wave effect into account, longitudinal vibration of pile and its application is systematically investigated
本文從三維軸對稱土體模型出發，在考慮樁周土體三維波動效應情況下，較系統地對樁的縱向振動特性進行了研究。In contrast to the existing methods which can detect one type of symmetry, the advantage of the algorithms is that it can detect both type and axis of symmetry
實現了物體對稱類型的判別和對稱軸的確定。這種方法克服了現有方法只能驗證一種對稱類型的缺點，即使缺失部分信息也能檢測出對稱性。A coaxial micro - pulsed plasma thruster ( micro - ppt ) improved from the standard pulsed plasma thruster ( ppt ) is drawing attention by its advanced properties of low volume, high isp, high efficiency and stabilization. a coaxial micro - ppt using solid inert propellant teflon has been made in center for space science and applied research ( cssar ), chinese academy of sciences
針對應用於微小衛星的電推進技術，各國爭相開展相關的研究，其中一種經由傳統的平行板電極ppt改進的同軸型脈沖等離子體微推進器（以下簡稱同軸型微ppt ）由於其尺寸小、比沖高、效率高、工作可靠等特點尤其受到關注。To predict the settlement of surrounding soils during excavation, axisymmetric model was established in fem software to analyze the problem by use of fem based on the biot ' s consolidation theory
為預測基坑開挖及降水過程中周圍土體的沉降，本文採用基於比奧固結理論的有限單元法在大型有限元軟體中建立軸對稱模型進行了分析。In the paper, consolidation effects on stress and displacement distributions are n ' t taken into consideration due to supposing that foundation soil consolidation has completed after surcharging preloading. based on the inherent anisotropy and induced anisotropy of foundation soil body, transversely isotropic elastic constitutive relations are adopted to simulate half - space clastic foundation body. the relations between displacement and displacement function are proposed by extending t, ove displacement function to transversely isotropic elastic half - space
本文假設地基土體是經過超載預壓處理過的，固結已經完成，不考慮固結對應力、位移場分佈的影響；基於地基土存在著固有各向異性和誘發各向異性，在前人的基礎上對e地基模型進行修正，採用橫觀各向同性彈性模型模擬無限彈性半空間，將love位移函數推廣到半空間，得到位移與位移函數之間的關系，然後經過hankel變換得到非軸對稱問題位移、應力的一般解。分享友人