軸承內孔 的英文怎麼說

中文拼音 [zhóuchéngnèikǒng]
軸承內孔 英文
bearing bore {hottag
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. Gd linear ball bearings ( drawn cup recirculating ball linear bearings ) are made of punched and quenched outer ring and plastic cage with a set of rolling ball

    Gd直線運動球軸承（沖壓外圈循環式直線運動軸承） ，由一沖壓且淬硬的外圈和帶一組鋼球的塑料導引保持架所構成一完整的裝配單元，可直接壓入座孔內。
  2. There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings

    軸瓦內表面的不承擔載荷部分開有油槽，潤滑油通過進油孔和郵溝流進間隙。
  3. In this section the author analyses the rules of the pile ultimate tip resistance and the shaft friction resistance distribution and their exertion of cast - in - place socketed piles instrumented with strainometers in soft muddy rock. the second aspect of the paper is the analysis on the current rock pile vertical bearing capacity in the four standards gb50007 - 2002, tb 10002. 5 - 99, jtj024 - 85 and jgj94 - 94, then the design method with correlated formula of socketed piles in xigeda - mudstone is given. at the end of this paper, based on the research of pressure grouting technique in recent years, and combined with in - site test result, this paper puts forward the design and calculation method to grouted pile in xigeda - mudstone and the principle of choosing grouting parameters, which provid es experiences for applying this technique and further studying

    本論文結合省級科研項目「西攀高速公路昔格達組泥巖層中鉆孔樁提高承載力的研究」 ，所做的研究工作主要在以下三個方面：一是根據8根樁身內埋設量測元件試樁的單樁豎向靜載荷試驗資料，分析了各試驗樁特別是常規沖孔灌注嵌巖樁在昔格達泥巖中的軸向力、側摩阻和樁端阻力的分佈和發揮規律；二是在討論現行規范對嵌巖樁承載力的計算公式的基礎上，探討了在昔格達泥巖層中的沖孔灌注嵌巖樁的側摩阻和端阻的計算方法，並推薦了相應的計算公式；最後，在吸取近年來對灌注樁后注漿技術研究成果的基礎上，結合現場試驗研究結果，分析了該項技術在昔格達巖層中的應用效果，提出了相應的參數選取，從而為壓力灌漿技術的工程應用和進一步研究提供經驗，並為今後在該地層中合理選用樁型以及指導施工提供了依據。
  4. 3. sliding bearing and isolation cover are the key parts which influence magnetic force pumps " safely running, pump ' s interior pressure and cooling holes are induced through analyzing outer and inside alnicos, sliding bearings " cooling flux

    滑動軸承和隔離套是影響磁力泵可靠性的關鍵部件，通過分析冷卻內外磁鋼和滑動軸承的冷卻流量，反推計算出泵內壓力場，給出冷卻孔設計的方法。
  5. This special heat - treatment ensures full bearing performance and prevents the set screws from loosening during operation as the set screws can be tightened hard enough without causing broken inner ring set screw hole

    內圈螺釘孔周圍經局部高溫回火后，軸承獲得更好的性能，可防止螺釘在軸承工作期間松脫，同時螺釘擰得緊也不會導致內圈爆裂。
  6. Through the experimentation for the physical performance of cfpb masonry under local compression, the author has observed the deformation and failure of cfpbm. based on the mathematical statistics and regression analysis of the experimental data, the author derived a feasible and common formula for counting the cfpbm ' s local compression strength regarding the different local compression locations, analyzed stress distribution of local bearing masonry under beams end, and provided the calculating formula on effective supporting length of beam end in brick masonry. as the results of experiments demonstrate, owing to the cfpb ' s own holes " system, the beneficial effects, the bounding effect of surrounding masonry and the spread effect of force, have not developed completely

    試驗結果分析表明：由於多孔磚自身的孔洞結構，砌體內部的圍箍作用和力的擴散作用未得到充分發揮，局壓強度雖較軸心受壓強度有所提高，但仍低於同情況下實心磚的局壓強度；當有上部荷載作用時，對砌體局壓有利的懸臂卸荷作用和內拱卸荷作用均不明顯，因此在推導梁端局壓強度計算公式時，未考慮此可能存在的有利影響，計算偏安全；局壓強度提高系數公式除採用規范公式（二項式）的表達式，還用對數式進行了回歸推導，得到了一個較為普遍的公式；論文還對梁端局壓的梁端有效支承長度計算公式進行了回歸推導。
  7. In case that the rolling bearings with no inner ring or outer ring and without inner and outer rings ars selected, the sueface haedness of the holes or housing holes as race, the working accuracy and surface quality shall be similar with the race of bearing rings in order to guarantee that loading capacity and operating performance are identical with the bearings equipped with rings

    選用無內圈或無外圈，以及無內、外圈滾動軸承時，作為滾道的孔或外殼孔表面的硬度、加工精度和表面質量應與軸承套圈的滾道相仿，以保證負荷能力和運轉能與有套圈軸承相同。
  8. The reliability is validated further on. 3. the static loading test is modeled by plaxis, based on this, the basic bearing mechanism is analysed which comprise the rule of the load - settlement curves, inner and outer friction resistance, end bearing, stress distribution along pile depth and the dissipation of excess pore pressures

    應用plaxis程序模擬單樁靜載荷試驗的過程，並根據計算結果較為詳細的分析了pcc單樁的基本承載特性，主要包括荷載?沉降曲線的特徵、樁壁內外側摩阻力的分佈、樁端阻力的分佈、樁的軸向荷載傳遞以及孔壓消散規律等。
  9. With two structures of bore cylindrical or tapered and retainers made of steel sheet or synthetic resins, the bearings are characteristic of their spherically formed outer ring raceways allowing for misalignment within 3 degree deflection between inner ring and outer ring, so as to compensate concentricity and deflection errors

    詳細信息:調心球軸承由圓柱孔和圓錐孔兩種結構，保持架的材質有鋼板、合成樹脂等，其特點是外圈滾道成球面形，具有自動調心性，可以補償不同心度和軸撓度造成的誤差，但其內、外圈相對傾斜度不得超過3度。
分享友人
分享到 Line

分享到臉書