軸承吊架 的英文怎麼說

中文拼音 [zhóuchéngdiàojià]
軸承吊架 英文
bearing suspension
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 吊 : hangsuspend
  • 架 : Ⅰ名詞1 （用來放置東西或支撐物體等的東西; 架子） frame; rack; shelf; stand 2 （毆打; 爭吵） fight;...
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. Fsb series fluoroplastic alloy pump is composed of pump body, impeller, back cover, seal, support, pump shaft, bearing, coupling, fasten bolt, nut and base plate

    Fsb系列氟塑料合金泵由泵體、葉輪，后蓋，密封性，支架，泵軸，軸承，連軸器，吊緊螺栓，螺母，底板組成。
  2. The top end bracket shall be fitted with a stainless steel lifting bail and shall be capable of supporting the combined weight of the pump and motor

    頂部尾軸承架應該配置不銹鋼吊環，應該能夠支撐泵和電機的總重量的壓力。
  3. The top end bracket shall be fitted with a lifting bail and shall be capable of supporting four ( 4 ) times the combined weight of the pump and motor

    頂部尾軸承架應該配置吊環，應該能夠支撐泵和電機的總重量四（ 4 ）倍的壓力。
  4. Based on practical project of inspecting, appraising and reinforcing a main heavy factory building, especially its steel crane girder system, of the second steel mill belonging to taiyuan steel & iron corporation, whose technology renovation leads to increase tonnage of many heavy cranes and vertical load of frame - bent structure, first the structure and its members were investigated, inspected, calculated and analyzed, and their reliability was appraised respectively and the strengthening projects or the measures to remedy were given. then, in accordance with the requirement to strengthen the girders under non - stop production, the feasibility of strengthening the crane girders by adding steel diagonal braces underneath the existing girders has been studied by inspecting and evaluating the strengthening effect of the crane girders and comparing with other reinforcing scheme

    本文結合太鋼（集團）有限公司第二煉鋼廠主廠房由於生產工藝改造要求，加大多臺重型吊車噸位及bc跨（ 1 ） （ 8 ）軸線框排架各層豎向（設備）荷載后，對廠房結構，尤其鋼吊車梁系統進行檢測鑒定與加固設計的實際工程，首先對廠房結構進行了現場調研、技術檢查、測試以及內力和承載能力的計算與分析（考慮抗震） ，並根據檢測、計算與分析結果，對廠房結構、構件的可靠性進行了評定，並綜合提出鑒定結論和加固處理建議。
分享友人
分享到 Line

分享到臉書