軸承寬度 的英文怎麼說

中文拼音 [zhóuchéngkuāndù]
軸承寬度 英文
bearing width
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. The narrower bearings required less distance to develop full width films.

    狹軸承只需要較短的距離就能產生全寬度潤滑膜。
  2. A way to avoiding crack or reducing crack width of concrete or reducing distortion of member is using prestressed concrete. the writer tried to make full use of the merit of the prestressed concrete and designed prestressed concrete mandril to control crack of structure. the prestressed concrete mandril, which was firstly applied high pressure on a small concrete bar, and then was made in concrete, so it would act as reinforced bar and resist load. in this thesis the writer designed 24 mmnbers and had experimental study of them, reached the conclusion that the effect of resisting crack of the prestressed concrete mandril was good when the load was not large, it can enhance the capacity of resisting crack and reduce the crack distance and crack width, but when the loads was large, the effect of resisting crack was not good, when we used the prestressed concrete mandril and reinforced bar together in member, the effect of resisting crack was very good. the writer analysed the adherence mechanism and wreck mechanism of the prestressed concrete mandril in anxial tension members, and according to the character of the prestressed concrete mandril, the writer constructed the bond model of it. then the writer introduced the analysis theory of crack including the bond - slip theory, the non - slip theory, the synthesis theory and mathematics stat method. the different theory had different theory base, they considered that the primary affection of crack width was different. in this test, the crack distance and crack width of members which placed reinforced bar were match to the compute value of the code gb 50010 - 2002 very well. to the members which

    本文共進行了24根試件的試驗研究，得出了預應力混凝土芯棒能較大地提高構件抗裂承載力，在荷載小於預應力混凝土芯棒的開裂荷載時有較好的抗裂效果，能較大地減小裂縫間距和裂縫寬度，但是當荷載較大預應力混凝土芯棒開裂時預應力混凝土芯棒的抗裂效果不是很好，若將普通鋼筋和預應力混凝土芯棒一起使用時則有很好的抗裂效果。本文分析了預應力混凝土芯棒在軸拉試件中的粘結機理和破壞機理，根據預應力混凝土芯棒本身的特點，提出了預應力混凝土芯棒與后澆混凝土之間的粘結模型。然後本文詳細介紹了經典的裂縫分析理論粘結滑移理論、無滑移理論、綜合理論和數理統計方法，各理論有著各自不同的理論基礎，認為影響裂縫寬度的主要影響因素也各不相同。
  3. At the same time, the program corresponding to the proposed method is compiled in fortran90, which is used to analyze the influence of several factors on behaviour of barrettes, including ratio of length to width, ratio of depth to equivalent diameter, ratio of modulus of pile to soil, possion ' s ratio, the finite layer etc. many useful conclusions are obtained from the above analyse

    該方法考慮了壁板樁樁身橫截面的非軸對稱性，並用fortran語言編制了相應的程序，進而分析了多種因素對壁板樁承載特性的影響，包括長寬比、樁徑比、樁土剛度比、泊松比以及有限壓縮層深度等。
  4. Verification regulation of instruments for measuring rolling bearing width

    滾動軸承寬度測量儀檢定規程
  5. Ball bearings with spherical outside surfaces and extended inner ring width

    球形外表面和擴展內環寬度的滾珠軸承
  6. Rolling bearings - bearings with spherical outside surface and extended inner ring width - part 1 : insert bearings

    滾動軸承.帶球形外表面和增加內環寬度的軸承.第1部分
  7. In fact, the bearing with finite width are widely used in rotational machinery. but the calculation of oil - film force of this kind of bearing needs a large mount of time, and analytical method is powerless to this problem. considering of above reasons, this paper leads into averageing natural value method that can meet the requirment of engineering

    鑒于工程中廣泛使用有限寬軸承，而對于這種軸承的油膜力的計算，採用數值方法計算工作量很大，而解析法又無能為力的情況，本文引入了一種適用於工程精度要求的平均本徵值法。
分享友人
分享到 Line

分享到臉書