軸承綜合 的英文怎麼說

中文拼音 [zhóuchéngzōnggě]
軸承綜合 英文
bearings in general
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 綜 : 綜名詞[紡織] （織布機上使 經線交錯著上下分開以便梭子通過的裝置; 綜片） heddle; heald
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  • 綜合 : 1 （歸在一起; 聯合成一個統一的整體） synthesize 2 （不同種類、不同性質的事物組合在一起） syntheti...
  1. These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc. according to these analyses, the possible way for improving the dynamic function of three - ring transmission may be put forward

    這些設計參數包括：行星軸承剛度、齒輪綜合嚙合剛度、輸出軸支承軸承剛度、內齒板質量、齒輪嚙合角、輸入軸和支承軸間距及輸入轉速等，根據這些分析，可以提出改善三環傳動動態性能的可能途徑。
  2. The composite grips extend bearing life, while working with the innovative two - stage dampening to give the n9 incredible flight characteristics

    綜合槍柄軸承延長壽命，同時與創意兩階段調高給n9不可思議的飛行特性
  3. Now developing successfully “ gearbox synthetic inspection instrumentation ” can measure simultaneously the first and second bearing bore diameter and verticality parameters of gearbox case. information acquisition and data processing is controlled by computer. the instrumentation improves the inspection efficiency and meets the demand of mass - produced

    本課題研製的變速箱殼體綜合檢測儀可實現在線檢測變速箱殼體一軸軸承孔直徑、二軸軸承孔直徑、一軸端面垂直度、二軸端面垂直度等幾何參數。
  4. Based on practical project of inspecting, appraising and reinforcing a main heavy factory building, especially its steel crane girder system, of the second steel mill belonging to taiyuan steel & iron corporation, whose technology renovation leads to increase tonnage of many heavy cranes and vertical load of frame - bent structure, first the structure and its members were investigated, inspected, calculated and analyzed, and their reliability was appraised respectively and the strengthening projects or the measures to remedy were given. then, in accordance with the requirement to strengthen the girders under non - stop production, the feasibility of strengthening the crane girders by adding steel diagonal braces underneath the existing girders has been studied by inspecting and evaluating the strengthening effect of the crane girders and comparing with other reinforcing scheme

    本文結合太鋼（集團）有限公司第二煉鋼廠主廠房由於生產工藝改造要求，加大多臺重型吊車噸位及bc跨（ 1 ） （ 8 ）軸線框排架各層豎向（設備）荷載后，對廠房結構，尤其鋼吊車梁系統進行檢測鑒定與加固設計的實際工程，首先對廠房結構進行了現場調研、技術檢查、測試以及內力和承載能力的計算與分析（考慮抗震） ，並根據檢測、計算與分析結果，對廠房結構、構件的可靠性進行了評定，並綜合提出鑒定結論和加固處理建議。
  5. The optimum design of the beat back - impact crusher is proposed, which aims at the highest efficiency of the machine work. the optimum designed mathematics model of the main structural dimension of the crusher ( m, xc, s, w 2 > ir ) is built with restraining conditions such as force condition, energy condition, hammer steady condition, no moving interference, strength of spin axle and bearing condition, upper limit and lower limit of the design variant condition etc. finally, an example is give to illustrate the efficiently of the method proposed

    在綜合考慮影響破碎機效率的各因素的情況下，提出了滿足以力，能量，錘頭穩定性，幾何條件，不發生運動干涉，轉子軸和滾動軸承的強度等約束條件，建立了包含破碎機關鍵參數（錘頭質量m ，軸心o到銷軸錘頭接觸距離r ' ，四川大學碩士學位論文錘頭質心到銷軸與錘頭接觸點的距離拙，錘頭與巖石碰撞到銷軸與錘頭接觸點的距離s ，轉子的速度。
  6. The synthetical stiffness of ball bearings is obtained by combination the contact stiffness with the oil film stiffness. the concept and the calculation menthod of the equivalent stiffness are presented in this paper

    將油膜剛度和接觸剛度組合，推導了滾動軸承的綜合剛度，提出了滾動軸承等效剛度的概念和計算方法。
  7. This dissertation made a systematic and profound research on fault analysis of expert system is put forward. the function modelling and the information modelling for faes is established. it probes into the knowledge described and processed, the knowledge maintenance, management and layout of the faes system ; and develop faes based on product facing the quality layo ut

    主要工作包括：對故障分析方法進行了全面深入的研究，在此基礎上，提出了質量規劃綜合分析方法的系統框架，重點分析了故障分析專家系統（ faes ）的體系統結構和功能模型，對faes系統的知識描述、處理、和維護進行了探索和研究，並以軸承為研究對象對系統進行了詳細的說明。
  8. The research works and conclusions of this paper as following : 1. besed on the test results published over the word of reinforced concrete beams without web reinforcements and with stirrups, the systematically statistical analysis is carried out to set up the fomula of shear resistance of reinforced concrete beams using the uniaxial tensile strength of concrete. it provided the basis of strtistical analysis for shear resistance of steel fiber reinforced concrete beams

    根據收集到的國內外對鋼筋混凝土無腹筋梁和鋼筋混凝土有腹筋梁的斜截面承載力試驗研究成果，進行了比較系統的綜合統計分析，提出了採用混凝土軸心抗拉強度研究成果，進行了比較系統的綜合統計分析，提出了採用混凝土軸心抗拉強度指標的鋼筋混凝土梁斜截面承載力計算公式，為鋼筋鋼纖維混凝土梁受剪承載力試驗結果的統計分析提供了基礎。
  9. As the counteraction of the behavioralism and grand theory, historical institutionalism developed a new theory pattern of institutionalism, in this pattern, it inherited the tradition of attach importance to institutions in old institutionalism on one hand, and integrated the new marxism and new webberism on the other hand

    作為對六、七年代盛行的行為主義和宏大理論的反動，歷史制度主義一方面繼承了舊制度主義重視制度的傳統，另一方面又通過對新馬克思主義和新韋伯主義理論的綜合，在制度的中軸上發展出一套新的理論模式。
  10. A way to avoiding crack or reducing crack width of concrete or reducing distortion of member is using prestressed concrete. the writer tried to make full use of the merit of the prestressed concrete and designed prestressed concrete mandril to control crack of structure. the prestressed concrete mandril, which was firstly applied high pressure on a small concrete bar, and then was made in concrete, so it would act as reinforced bar and resist load. in this thesis the writer designed 24 mmnbers and had experimental study of them, reached the conclusion that the effect of resisting crack of the prestressed concrete mandril was good when the load was not large, it can enhance the capacity of resisting crack and reduce the crack distance and crack width, but when the loads was large, the effect of resisting crack was not good, when we used the prestressed concrete mandril and reinforced bar together in member, the effect of resisting crack was very good. the writer analysed the adherence mechanism and wreck mechanism of the prestressed concrete mandril in anxial tension members, and according to the character of the prestressed concrete mandril, the writer constructed the bond model of it. then the writer introduced the analysis theory of crack including the bond - slip theory, the non - slip theory, the synthesis theory and mathematics stat method. the different theory had different theory base, they considered that the primary affection of crack width was different. in this test, the crack distance and crack width of members which placed reinforced bar were match to the compute value of the code gb 50010 - 2002 very well. to the members which

    本文共進行了24根試件的試驗研究，得出了預應力混凝土芯棒能較大地提高構件抗裂承載力，在荷載小於預應力混凝土芯棒的開裂荷載時有較好的抗裂效果，能較大地減小裂縫間距和裂縫寬度，但是當荷載較大預應力混凝土芯棒開裂時預應力混凝土芯棒的抗裂效果不是很好，若將普通鋼筋和預應力混凝土芯棒一起使用時則有很好的抗裂效果。本文分析了預應力混凝土芯棒在軸拉試件中的粘結機理和破壞機理，根據預應力混凝土芯棒本身的特點，提出了預應力混凝土芯棒與后澆混凝土之間的粘結模型。然後本文詳細介紹了經典的裂縫分析理論粘結滑移理論、無滑移理論、綜合理論和數理統計方法，各理論有著各自不同的理論基礎，認為影響裂縫寬度的主要影響因素也各不相同。
  11. Firstly, considering the molecular pump is small and the elimination of heat condition is bad, this paper presents the structure of the mb, including the material of the rotor and stator, the number of magnetic poles, the stator slot shape of mb, the layout of the magnetic poles, the coins winding and so on

    首先綜合考慮了分子泵體積小、磁軸承散熱條件不好的特點，設計了分子泵磁懸浮軸承的結構，選擇了軸承鐵芯的材料，設計了磁極的布置、槽的形狀、磁極數目和線圈纏繞方式。
  12. The experiment results show that the rotor can be suspended with dc when adopting motor ' s coiling method, which testifies the feasibility of integrative control by adding ac to windings coiled in this method, and lay out good foundations for further investigation

    實驗結果表明，在電機繞線方式下能夠進行轉子的懸浮實驗，從而證明了採用電機繞線法進行動力磁軸承交流綜合控制實驗的可行性，為今後的深入研究工作打下了基礎。
  13. Guizhou qiannan slide bearing co., ltd. lie in in the beautiful plateau bridge city - it is even, it is a comprehensive high - tech enterprise incorporating slipping the development, production and sales and service of the bearing into an organic whole

    貴州黔南滑動軸承有限責任公司位於風景秀麗的高原橋城-都勻，是一家集滑動軸承的開發生產銷售和服務為一體的綜合性高科技企業。
  14. Considering the local nonlinearity of the rotor - bearing system, a systematic dimension reduction method is applied in this paper for low - pressure rotor - bearing of the 200mw turbine set system. the model of the rotor - bearing system is established by fem ( finite element method ). the fixed - interface component mode synthesis procedure is applied to significantly reduce the dimension of the system

    本文針對200mw汽輪發電機組低壓轉子?軸承系統，採用了一種系統的降維分析方法:利用有限元方法建立了轉子?軸承系統的有限元模型，然後利用固定界面模態綜合法顯著地降低系統的維數。
  15. Loads for every bearing, rotary speed, bearing saddle vibration, shaft vibration, orbit of shaft center, were measured. severely rubbing fault was diagnosed by comprehensively analyzing these signals. the diagnosis results have a good agreement with situation

    測得了各支承負荷特性、軸的轉速、軸承座振動、軸的振動、軸心軌跡等數據信號，綜合分析了信號特徵，判定為嚴重碰摩故障，與停機檢查實際情況相當吻合。
  16. The lower - band spectrum caused by unbalancing rotor and eccentric error of primary axes is analysised firstly. the vibration of basic factors and its features caused by the basic member are discussed, such as turbo - propellers, planetary - reducer and bearings

    首先分析系統中由於主轉子動靜不平衡、主軸不對中而激發低頻諧波成分的現象，而後討論螺旋槳、行星減速器及軸承的振動故障機理以及整機振動綜合分析方法。
  17. Abstract : in this paper, the best selection of key parameter helix angle is discussed for all kinds of cross helical gear transmission in order to raise efficiency, reduce wear, obtain lighter weight and less size of bearing

    文摘:從提高效率、減少磨損、減輕重量和較小軸承尺寸的角度出發，綜合探討了交錯軸斜齒輪傳動的各種組合中，關鍵參數螺旋角的最佳選擇
  18. The basic theory of switched reluctance generators ( srgs ) is illustrated. by analyzing the control strategies of srg, three control strategies of bsrgs are suggested : current chopping control ( ccc ), angle position control ( apc ), pulse width modulation ( pwm )

    綜合普通開關磁阻發電機的電流控制方式，提出了無軸承開關磁阻發電機的三種控制策略:電流斬波控制策略（ ccc ） 、角度位置控制策略（ apc ） 、 pwm控制策略。
  19. The rule of the axial force distribution in the src column summarized, and a reasonable formula for the axial force level ’ s calculation in src column is offered for the design. besides, the aseismic analysis methods for the src structures are listed, and the dynamic time history analysis and static push - over analysis for the whole structure are done. the character of the earthquake response in this kind of structure is analyzed and some advice for actual design is proposed

    同時分析了src柱中的軸力分配規律，給出了比較合理的src柱軸壓比計算公式;另外綜合敘述了適用於src結構抗震分析的方法，並且運用常用的設計計算軟體對整體結構進行彈性的動力分析和靜力彈塑性分析，得出src柱對結構的整體抗震性能有提高，可以在保證豎向承載力的同時增大整體結構的抗側能力，為以後的實際設計提供一定的依據。
  20. At first the switching power amplifiers of the discrete components are researched and some application circuits for amb power amplifiers are developed. secondly the integrated power amplifier is discussed, a new type of pulse width modulation ( pwm ) power amplifier applying sa60 is designed and used in amb system. in the end of the dissertation several synthesized tuning measures and some experimental results for amb system are presented

    首先討論了分立元件開關功率放大器原理並研製了在電磁軸承中的應用電路；其次討論了集成功率放大器，應用sa60設計了新型脈寬調制功率放大器並在電磁軸承中應用；在論文的最後給出了電磁軸承系統綜合調試的一般方法及調試結果。
分享友人
分享到 Line

分享到臉書