軸承頂 的英文怎麼說

中文拼音 [zhóuchéngdǐng]
軸承頂 英文
lagerdom bearing hub
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 頂 : i 名詞（人體或物體的最上部） crown; peak; top Ⅱ動詞1 （用頭支承） carry on the head 2 （從下面拱...
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. Thedevelopment development hydraulic jack, the bearing heater, thebearing get up pulling out, the hydraulic pressure spanner, thehydraulic pressure pulls a horse, the hydraulic pressure small crane, nut broken cutting, the oil filter machine and the pipe bendingmachine and so on the advanced practical mechanical and electricalservice product has the world advanced level, the product and thetechnology widely applies to domain the and so on electric power, petrification, chemical industry, metallurgy, mine, spinning andweaving, papermaking machinery service department and the machinemanufacture unit, and in the daya bay nuclear power station, beijingsteel corporation, wuhan steel corporation, the baoshan steelcorporation, the daqing oil field, the victory oil field, the golmudoil field, the three gorges power plant, yangzi petrifies, qi and lupetrifies and so on in the national large and middle scale enterprisesand the project the comprehensive promoted use

    研製開發的液壓千斤頂，軸承加熱器、軸承起拔器、液壓扳手、液壓拉馬、液壓小吊車、螺母破切器，濾油機和彎管機等先進實用的機電維修產品有世界先進水平，產品和技術廣泛應用於電力、石化、化工、冶金、礦山、紡織、造紙等領域的機械維修部門和機械製造單位，並在大亞灣核電站、首鋼、武鋼、寶鋼、大慶油田、勝利油田、格爾木油田、三峽電站、揚子石化、齊魯石化等國家大中型企業和工程中全面推廣使用。
  2. The top end bracket shall be fitted with a stainless steel lifting bail and shall be capable of supporting the combined weight of the pump and motor

    頂部尾軸承架應該配置不銹鋼吊環，應該能夠支撐泵和電機的總重量的壓力。
  3. The top end bracket shall be fitted with a lifting bail and shall be capable of supporting four ( 4 ) times the combined weight of the pump and motor

    頂部尾軸承架應該配置吊環，應該能夠支撐泵和電機的總重量四（ 4 ）倍的壓力。
  4. Unclamp the shaft from the vise and slide off the top bearing

    松開老虎鉗上的軸，將頂部軸承移出。
  5. The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio

    基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。
  6. This paper outlines operation, check and repair of the bucket stacker / reclaimer of a coal conveying system used at anqing petrochemical coal - fired power station, describes damage condition of the slewing ring, discusses the causes and details how to replace the damaged slewing ring by synchronously jacking

    摘要介紹了安慶石化熱電廠輸煤系統斗輪堆取料機的使用檢修和回轉大軸承的損壞，分析了損壞原因，重點介紹了「頂升法」更換回轉大軸承的技術。
  7. Ball and roller bearing top rollers for ring spinning frames and for roving frames

    環錠精紡機和粗紗機用滾珠和滾柱軸承頂端滾柱
  8. It could be seen that the curve of settlement and load of pile, the distribution of axial force on the pile top, the curve of load on cap and axial force on the top pile obtained with numerical analysis were agreed with those measured in centrifugal model test

    分析結果表明，數值分析所得承臺沉降與承臺荷載的關系曲線、樁頂軸力分佈、樁頂軸力隨承臺荷載變化的關系曲線，與其離心模型試驗實測成果較一致。
  9. The seat material shall be one of the following materials : ethylene - propylene - diene monomer ( epdm ) or fluoroelastomer ( fpm ) with polytetrafluoroethylene ( ptfe ) bearing support at the top and bottom

    閥座材料應該是下列材料之一：乙烯-丙烯-二烯系單體（三元乙丙橡膠）或氟橡膠（ fpm ） ，在頂部和底部配置聚四氟乙烯（ ptfe ）軸承支撐。
  10. Slide the top bearing on the stem

    將頂部軸承移到閥桿上。
分享友人
分享到 Line

分享到臉書