軸箱體 的英文怎麼說

中文拼音 [zhóuxiāngtǐ]
軸箱體 英文
axle box body
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 箱 : 名詞1. （箱子） chest; box; case; trunk 2. （像箱子的東西） anything in the shape of a box
  • 體 : 體構詞成分。
  1. The crankcaseventilation system, using a road-draft tube, vented the crankcase vapors and blow-by gas into the atmosphere.

    採用行車抽吸管的曲軸箱通風系統，給曲軸箱內的蒸氣和竄漏氣體排入大氣提供了出口。
  2. One of the jobs of pcv system is to remove these crankcase contaminants before the rotating crankshaft mixes them with the oil.

    PCV系統的作用之一是，在旋轉的曲軸把水和液體汽油混合之前，把它們排出曲軸箱。
  3. The design optimization of jig construction, jig body, locating mechanism of crank case cores, jacket cores assembling vehicle and jig supporter was discussed

    對夾具結構、夾具本體、軸箱芯定位機構、水套砂芯組芯小車及夾具支架的設計優化進行了討論。
  4. The crankcase is the lower part of the engine cylinder block.

    曲軸箱是發動機氣缸體較低的部分。
  5. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  6. The product of electric furnace fittings including : micro - computer program temperature control instrument 、 refractory brick ( ultra - light weight energy saving brick ) 、 resistance wire 、 electroheat belts 、 electrical heat tube 、 silicon carbide rod 、 furnace bottom plate 、 muffle tank 、 vacuum sealed fan 、 wind wheel 、 axis 、 substructure 、 bin seat 、 flat shape plate 、 box 、 panel 、 weatherstrip plate 、 return air plate 、 bin 、 connection box 、 educe rod 、 thermocouple 、 thyristor 、 porcelain pipe 、 crucible 、 furnace chamber 、 furnace frame 、 charging bin 、 substructure 、 pit furnace cover lifter framework ( sole design ) and otherwise

    電爐配件產品包括：微電腦程序控溫儀、耐火磚（超輕質節能磚） 、電阻絲、電阻帶、電熱管、硅碳棒、爐底板、馬弗罐、真空密封風機、風葉、軸、底座、料筐座、扁形板、箱體、面板、擋風板、回風板、料筐、爐柵、接線盒、引出棒、熱電偶、可控硅、瓷管、坩堝、爐膛、爐門、爐框、裝料筐、底座、井式爐蓋升降機構（獨家設計）等。
  7. Blowby is basically the leakage of compressed air-fuel mixture and burned gases past the piston rings into the crankase.

    竄氣，基本上是被壓縮的空燃混合氣和燃燒后的氣體的泄漏，它通過活塞環進入曲軸箱。
  8. It whips and mixes the fresh air and crankcase fumes as it rotates.

    它旋轉時，把新鮮空氣和曲柄軸箱氣體攪混在一起。
  9. Analysis results of histogram statistics and section electron microscopic scan technique, are that fracture feature of the cracks of the hbbb is similar and the crack is multi - source strain fatigue one. internal defects of the cast, such as impurities, gas holes, etc, are the main causes for early cracks. the contrast analysis of static strength, model and transient respond on three structures with fem proves that geometrical stress concentration in partial area has influence on early crack, also

    利用直方圖等統計方法和電鏡掃描技術對該抱軸箱體裂紋分析的結果是：抱軸箱體的裂紋斷口特徵相近，裂紋性質屬于多源性低周疲勞裂紋，鑄件中的夾雜、氣孔等內部缺陷是導致過早裂損的主要原因；利用有限元法對該抱軸箱體三種結構的靜強度、模態和動態響應對比分析，證實了局部幾何性應力集中對過早裂損也有一定影響。
  10. Sun hydraulik gmbh offers offers to screw - in valves, globe valves and valve housing

    提供軸承箱、軸承體、閥體、閥箱、閥套、閥門外殼及其它產品。
  11. Therefore, the two schemes on the forge - weld hbbb are designed and trial - manufactured in the works

    為此，設計和試制完成了兩種方案的鍛焊組合結構抱軸箱體。
  12. Design improvement is in three stages partial, geometrical stress concentration improvement, pure casting technology improvement and a forge - weld box body design

    設計改進分三個階段，即局部幾何性應力集中改進、提高鑄造質量的純工藝改進和鍛焊組合結構抱軸箱體的設計。
  13. Put forward is the future plan on the improvement of the forge - weld hbbb, which is helped to research and design of the hbbb for the ss7 - type electric locomotive and other electric - driving locomotives in the future

    提出了鍛焊抱軸箱體攻關工作的進一步設想，對今後韶山7型電力機車抱軸箱體的進一步攻關及其它電傳動機車抱軸箱體的設計和研究，有一定的借鑒作用。
  14. Then the experiment platform of the hypoid gear system was set up, and the lateral, longitudinal and axial vibration response of the bearing and the vibration acceleration response on the surface of the gearbox were measured

    搭建了準雙曲面齒輪傳動系統的實驗平臺，測量了準雙曲面齒輪箱軸承座的橫向、縱向和軸向振動響應和箱體表面振動加速度響應。
  15. This model consists of three parts : frame, main shaft box and material holding shelf. supported by long axle, the main shaft box is an integral

    本機型由機架，主軸箱體，載料架三部分構成，其主軸箱為
  16. For mobile sources, meca members include manufacturers of catalytic converters ( catalysts, substrates, mounting sleeves, and converter housings ) for all fuels ; diesel particulate filters ; oxygen, nox, and temperature sensors ; thermal management strategies ; engine / fuel management technologies ; crankcase emission control technologies ; evaporative emission controls ; enhanced combustion technologies ; plasma / corona technologies ; and components for fuel cell technology

    在移動源方面，其成員主要從事下列產品或技術的生產或研發：各類燃料的催化轉化器（包括相關產品如催化劑、基質、安裝袖和轉化器殼） ；柴油顆粒過濾器；氧氣、氮氣和溫度傳感器；熱處理系統；發動機/燃料操控技術；曲軸箱排放控制技術；蒸發排放控制；強化燃燒技術；等離子體/電暈技術。
  17. Introduced is the install, bearing loads, structural features and service in electric - transmission locomotives

    介紹了抱軸箱體在電傳動機車上的安裝位置、承擔載荷、結構特徵和運行情況。
  18. Prolonging the fatigue life of the hbbb for the ss7 - type electric locomotive relies on improving cast process and cast quality

    提高韶山7型電力機車抱軸箱體使用壽命的出路在於改進鑄造工藝，提高鑄件質量。
  19. Summed up is the process of the crack treatment on spot, the theory analysis and the design improvement of the hugging - bearing box body ( hbbb ) for ss7 - type electric locomotive

    全面總結了韶山7型電力機車抱軸箱體在使用中發生裂紋的現場處理、理論分析和設計改進的過程。
  20. Railway rolling stock. method of testing roller bearing axle - box cases. thermal test on axle boxes test machine

    鐵路車輛.滾柱軸承軸箱體的試驗方法.在軸箱試驗機上進行的熱試驗
分享友人
分享到 Line

分享到臉書