軸驅動的 的英文怎麼說

中文拼音 [zhóuqūdòngde]
軸驅動的 英文
shaft driven
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 驅 : 動詞1. （趕） drive （a horse, car, etc. ） 2. （快跑） run quickly 3. （趕走） expel; disperse
  • 的 : 4次方是 The fourth power of 2 is direction
  • 驅動 : [機械工程] drive; prime mover
  1. Nf - 6 wind tunnel is a pressurizing, continuous, high - speed and return - flow aerofoil wind tunnel

    Nf - 6風洞是一座由軸流式壓縮機驅動的增壓、連續、高速迴流式翼型風洞。
  2. Driveequipment use active magnet connected - implement to firsthand fix at the axletree of electrical engine, pumproom close completely, via magnetic force coincidence to drive impeller on rotor - assembled to circumgyrate indirectly

    驅動裝置採用主動磁鐵聯軸器直接裝在電機軸上，泵室完全封閉，通過磁力偶合間接驅動轉子組合上的葉輪旋轉。
  3. So it is necessary to study the driving structure and control scheme of new system radar in order to track continuously in whole hemisphere without blind zone

    因此，研究新體制的三軸雷達的驅動結構及控制方案以實現大於半球的全空域無縫隙連續跟蹤就變得十分必要。
  4. Cranes ; evaluating of cardan shafts for travelling drives

    起重機.移動驅動用萬向軸的評價
  5. Driveequipment use active magnet connected - implement to firsthand fix at the axletree of electrical engine, pumproom close completely, via magnetic force coincidence to drive impeller on rotor - assembled to circumgyrate indirectly, it own the trait like tightly structure handsome exterior small bulk laigh noise unfailingly move expediently service using safety and economize etc

    ，驅動裝置採用主動磁鐵聯軸器直接裝在電機軸上，泵室完全封閉，通過磁力偶合間接驅動泵軸上帶磁鐵的葉輪旋轉，具有結構緊湊
  6. Gear a, at the end of the drive shaft, and gear b, on the countershaft, are in constant mesh

    齒輪a位於驅動軸的末端，齒輪b在副傳動軸上，它們恆定嚙合。
  7. Driving power for the cutting tool comes from the rotation of the spindle, which is a hollow shaft that rotates in bearings.

    刀具的驅動力來自主軸的旋轉，主軸則是一根在軸承中旋轉的空心軸。
  8. As long as the truck is moving in a straight line, the ring gear, differential gears, and drive axles turn together without variation of speed

    當卡車直線行駛的時候，環形齒輪，差速器齒輪和驅動軸便會無變速的一起轉動。
  9. Axle driven electric generator

    車軸驅動的發電機
  10. The magnetic suspension bearingless motors generate both electromagnetic torque and magnetic levitation forces for the rotor suspension by the motor itself. the bearingless motor is comparatively suited for using as artificial heart blood pump motor due to the advantages of without mechanical wear and noise, structure compact and contactless

    磁懸浮無軸承電機定、轉子既用於產生驅動力矩，同時又用於產生支撐轉子的磁懸浮力，具有無機械磨損、噪音小、可高轉速和體積小等特點，比較適用於人工心臟血泵電機。
  11. This paper introduced the design of the driving system of a warp beam in which a step - motor was adopted as the let - off motor

    介紹了採用步進電機作為送經電機的織軸驅動系統的設計。
  12. By comparing dc, ac and step - motors and analyzing the driving characteristics of the warp beam, a conclusion was drawn that a higher performance to price ratio could be got when a step - motor was selected for the warp beam

    通過對直流電機、交流電機和步進電機的比較，結合織機的織軸驅動特點，得出選用步進電機有較高性價比的結論。
  13. Abstract : a new type cold frame is intruduced. the deformation of unsymmetry section steel after cooling is mainly eliminated by reversely curring it on line, ensuring the achievement of automation of meticulous repair. at the same time the disposing principle of equilibrium weight on the driving axis of cold frame drived by eccentric wheel was improved. the torsional moment of transmission shaft and power of electric motor are reduced by the method

    文摘:介紹了一種新型冷床，通過在線對非對稱型鋼進行反向彎曲，基本上消除了非對稱型鋼冷卻后的變形，保證了精整工序自動化的實現.同時，提出了偏心輪驅動的冷床驅動軸上平衡重的配置原則.此方法可降低傳動軸上所受的扭矩，減少了電動機的功率
  14. The length of line is prolonged without increasing of driving. its driving spindle is to drive single roller to form accumulation

    在不增加驅動的前提下能有效的延長線體的長度，其傳動軸為驅動單根滾筒，從而形成堆積。
  15. The accelerating and decelerating of the step - motor during weaving and its driving principle were discussed, and the calculating method for parameters of the mechanical driving system was expounded with examples

    分析了步進電機在織造過程中的加減速控制方法以及步進電機的驅動原理，闡述了織軸驅動系統機械傳動的參數計算方法，並以示例進行了說明。
  16. Through militia programs, the final plan is to change the transmission ratio of gearbox, the parameter of friction piece as well as the gear width of the sixth gear of the second shaft. finally, the parts of transmission system - clutch, gearbox, driving shaft, driving bridge are checked and the problems are solved

    本文通過多目標規劃，最終的優化方案是適當改變變速器傳動比、摩擦片參數及二軸六檔齒輪齒寬，最後對傳動系各部件- - -離合器、變速器、傳動軸、驅動橋等進行了校核，使問題得到妥善解決。
  17. Furthermore, it discusses how to figure out these models mentioned above. with reference to the design of various automobiles, it primary defines the method to get key parameters in platform lorry general design, and creates mathematical model. it provides more reference to choose axis, driving axle, number of arrest axles, type of tire, pump, motor, lift hydrocylinder, maximum payload and sole weight reasonably

    在參考各類汽車設計思想的基礎上，根據理論推導和經驗公式的計算，初步確定了平板車總體設計階段的主要技術參數的求解方法，建立了數學模型，為合理地選擇軸、驅動橋、制動橋個數，輪胎型號、泵、馬達、舉升油缸、平板車的最大載重量和自重的選擇等提供了依據。
  18. At present the power transmission system of electric mobile is based on series of experiments that destroy parts of the transmission shaft, driving axle, power transfer, gear - box to reach the goal for the test of the limit of working condition of mobile

    目前電動汽車傳動系統試驗主要靠對傳動軸、驅動橋和分動器和變速箱等零部件做一系列破壞性試驗，以達到對汽車產品極限工況的檢測。
  19. The cutter location in nc generative ultrasonic grinding process for parallel ruled surface with cylindrical grinding wheel was analyzed, the structure of nc generative ultrasonic grinding device was introduced, the design of grinding spindle assembly and the spindle ' s driving scheme was also introduced, system hardware and software design had been finished

    摘要分析了圓柱磨輪數控展成超聲磨削平行直紋面時的刀具空間位置，介紹了數控展成超聲磨削成形加工機床的總體結構，論述了磨輪主軸部件設計及主軸驅動方案，實現了主軸變頻調速控制系統軟硬體設計。
  20. The constitution of control system of high - speed cnc engraving and milling machine is analyzed in chapter 3, given emphasis to motion controller, spindle driver and feed driver

    第三章分析了計算機高速數控雕銑伺服系統的構成，著重研究了運動控制器、主軸驅動部分和進給驅動部分。
分享友人
分享到 Line

分享到臉書