載頻重置 的英文怎麼說

中文拼音 [zǎibīnzhòngzhì]
載頻重置 英文
carrier reinsertion
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 重置 : resetting重置方式 reset mode; 重置價值折舊 depreciation on replacement value; 重置資產 replacement assets
  1. The soft switching, phase - shifted pwm and bi - directional dc - dc converter hang together, depress circuit switching loss and noise effectively, which provide condition to increase switch frequency, efficiency and reduce size and weight for the converter ; at the same time, it is proved the converter can achieve zvs in larger load variation, and the converter has the virtue of structure compact, voltage and current stress small such as ordinary hard switch converter

    該變換器把軟開關技術和相移控制pwm技術以及雙向dc - dc變換器技術有機結合在一起，有效地降低了電路的開關損耗和開關噪聲，為變換器裝置提高開關頻率、效率以及降低尺寸及重量提供了良好的條件;同時，能拓寬零電壓開關的范圍，使變換器在較寬的負載變化范圍內都能實現軟開關。
  2. The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced

    論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。
  3. This article describes a way of special ultrasonic system which monitors thermal stress in seamless welded rails. this monitoring system is a non destructive testing system, which adopts avr mcu and high - precise time chip processing as the core of it, and adopts the critically refracted longitudinal wave as the object of measuring. my studying focuses on the theory of the monitoring system, which will be listed in this arctile : according to the snell theory, the theory of motivating of critically refracted longitudinal wave is described in details, and the finite element software is used to emulate the propagating course. the formulas of calculating the pts of swr are taken from the acoustoelasticity theory, and the calculating the parameters is introduced. according to assemble materials, three kinds of ways of monitoring the pts of swr using critically refracted longitudinal wave are described, which are measuring the sound - time in changeless distance, ultrasonic critical - angle refractomery and frequency spectrum, the first way of ways is used in this experiment system. the factors, which effect the monitoring system, are assaid in some degree based

    本文的研究工作重點在無縫焊接鋼軌溫度應力測量系統的理論模塊，包括根據snell原理，研究極限折射縱波的激發機理，並使用有限元軟體ansys進行模擬;根據聲彈性理論以及公式推導出計算無縫焊接鋼軌中的溫度應力的公式，並對其中參數的求解方法進行介紹;根據收集的資料，介紹了三種使用極限折射縱波測量無縫焊接鋼軌溫度應力的方法，即固定距離測量聲時法、臨界角折射法和頻譜分析法，本實驗系統使用的是第一種;根據實驗經驗以及相關資料，分析了影響極限折射縱波測量溫度應力的幾個因素，並提出了相應的解決方法;根據實驗系統的需要，獨立設計並加工出相關配套的實驗設備，包括實驗鋼塊、有機玻璃楔塊、固定件、載荷外框裝置等。
  4. For optical - layering approach, we propose an ant - based algorithm, which uses the ants " capability of finding shortest or near - shortest paths between a food source and their nests, to solve the logical topology reconfiguration problem. we give the ants routing formula based on dynamic load balancing and short path on the assumption that some conditions hold

    前者適合於業務矩陣變化不是太頻繁的網路，提出利用螞蟻演算法解決業務的再路由問題，即利用螞蟻具有找到最短徑及不同種類螞蟻具有互斥的天然特性來進行邏輯拓撲重配置，從而保證了鏈路負載分佈的平衡性。
分享友人
分享到 Line

分享到臉書