輥端 的英文怎麼說

中文拼音 [gǔnduān]
輥端 英文
roller end
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  1. Compared with punching process the continuous punching process has advantage of continuous operation and with cylindrical cutting process it has no cutting roller ' s drawback of not being able to reuse

    介紹了連續沖切式瀝青油氈瓦的生產工藝及設備。此生產方式既克服了一般沖切式不能連續作業的局限性，實現了連續工作的目標，又避免了滾切式中滾切輥一次性使用的弊端。
  2. It ` s suitable for the bend and deformation of the metal plates and it can roll the round and arcshapes and the cone ones within its specified ranges. it has the function of prebending the plate at both ends. the two lower rollers are the driving ones and can make the horizontal movement ; and the upper is a driven one and can make the up and down movement. the moving manner includes the mechanical and industry, boilers, shipbuilding, metal structure, machine manufacture and other trades, especially for the roll the steel trunks with smaller diameter and longer length in power transmission and trandform and other trades

    該機適用於金屬板材的彎曲成型，可卷制圓形，弧形和一定范圍的錐形工作，並有板材端部預彎功能，本機型兩個下輥為主動輥並可水平移動，上輥為從動輥上下移動，移動形式有機械式和液壓式，傳動軸均採用萬向連軸器連接，它廣泛適應于石油化工鍋爐造船金屬結構及機械製造行業，特別適用於送變電行業等直徑較小長度較長鋼管桿的卷制
  3. Materials enter from one end of the tube, grinded between tube and roll through leading equipment, the grinding times be changed

    其粉磨過程是：物料從磨圓筒的一端進入，通過導料裝置導向筒體與磨輥之間的間隙研磨。
  4. Concentricity analysis of hole throats on both ends of carrier roller

    托輥管體兩端孔頸的同軸度分析
  5. One end of belt - driven roller is fixed with machine body. the other end links with bolt - mode coupler at axial end of reducer. so that belt is easier replaced

    皮帶驅動輥筒一端固定於機體上，一端與減速機軸端插銷式聯軸器相連，使皮帶更換更容易。
  6. Interlocked swing open left and right top panels which stops the rolls and cuts of the electric supply when opened

    上端左右電櫃帶柔性自鎖，打開時輥及電源自動停止。
  7. The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction

    結果表明：壓制時間對齒形的變形影響較大，對齒型的影響很小；模擬軋輥壓制的鋸齒，根部一段幾乎沒有變化，是從一段距離開始變形，然後在頂端向相反的方向彎曲；壓製成型后，鋁板厚度的變化很小。
分享友人
分享到 Line

分享到臉書