輪廓滾形 的英文怎麼說
中文拼音 [lúnkuògǔnxíng]
輪廓滾形
英文
contour roll forming-
While actual profile lies on the type of cam mechanism, this paper take example for three kind of typical cam gear that is spire handspike disk cam mechanism, roller handspike disk cam mechanism and flat - bottomed handspike disk cam mechanism, and the design of cam actual profile is carried out. with the extensive application of computer and development of applied software, the computer - aided design is regarded increasingly
本文以配氣凸輪機構三種典型的類型，即尖端推桿盤形凸輪機構、滾子推桿盤形凸輪機構及平底推桿盤形凸輪機構為例，進行了凸輪工作輪廓線的設計隨著計算機的廣泛應用及應用軟體的不斷發展，內燃機配氣凸輪的計算機輔助設計日益受到人們的重視。Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve
建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。This paper provides the general equations of the theoretical contour line and the actual contour line of roller translation follower and roller oscillating follower disc cam in the polar coordinates system and the rectangular coordinates system, respectively. the equations are not only fit for the different layouts of the relative position of follower and cam, but also fit for the different types of cam contour
分別給出了滾子直動從動件和滾子擺動從動件盤形凸輪的理論廓線及實際廓線在極坐標系與直角坐標系下的通用方程，它們對于從動件與凸輪相對位置的不同布局方式及凸輪輪廓的不同類型均適用Based on the one - side processing technology, the dissertation proposes a new method of structure design and realizes the drive of sc by pure roller pairs of point engagement. this new drive mode apparently improves the driving accuracy, efficiency, life - span, movement and dynamic feature of scm
在凸輪廓面採用單側面加工工藝基礎上，提出了結構設計的改進形式，結合廓面修形方法，實現了空間凸輪機構點接觸的純滾動副傳動，顯然提高了機構的傳動精度、效率、使用壽命、運動性能和動力性能。The outline, size and preciousion of the roller are designed and manfactured according to technical need of processed spares, while equipment size is according to structure of the machine tool
金剛石滾輪的輪廓形狀、尺寸和精度是根據被加工零件的相應技術要求而設計製造的，安裝尺寸則根據用戶機床結構或要求而定。Contour roll forming
輪廓滾形分享友人