輪鍵槽 的英文怎麼說

中文拼音 [lúnjiàncáo]
輪鍵槽 英文
wheel key way
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  1. Table 5. the max key way stress of the contunious running gear sk

    表15 .連續工作輪的最大允許鍵槽應力sk
  2. A slot for a key in the hub or shaft of a wheel

    鍵槽輪子的轂或軸里的鍵的溝槽
  3. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
  4. If the confirmed size from the above formula is not practical, it is necessary to apply flange wheel hub and checking board, the checking board should be connected with gear with bolt, and the bolt should be on special pitch circle radius

    21 . 1如果從上面公式確定的鍵槽尺寸不實用，那麼應採用帶鍵的法蘭式輪轂和檢查板，檢查板用螺栓連接在輪上，螺栓處于特別的節圓半徑上。
  5. 12b twister adopt dual support, the main axis adopt thick seamless steel tube, through the keyway connect the winch and have good rigidity and no riding wheel ( 1 set of 12b assistant riding wheel ), adopt gear to back twist and the twister can rotating on high speed in long time

    5 18盤絞體採用雙支撐座支撐，主軸為厚無縫鋼管、通過鍵槽連接絞盤、具有鋼性好、輔助托輪2套，採用齒輪退扭、絞體可長期高速旋轉。
  6. The major conclusions of the article are : 1 ) it presents the methods of the key parameter selection and calculation of the gear pump, including the volumetric capacity, the gear profile and its parameter, the leakage, and input power. and it demonstrates the rationality of the parameter selection through experiments

    本論文的主要工作及結論如下： 1 ）給出了高參數齒輪泵關鍵技術參數的計算、選用方法，包括齒輪泵的轉排量、齒輪泵的轉子型式及其參數、齒輪泵的工作間隙、卸荷槽、齒輪泵的輸入扭矩的計算選擇方法，並用實驗方法檢驗了關鍵技術參數選擇的合理性。
  7. Ys for customers with the provided designation and dimensions of inner holes, key way and width ; also we provide service for the measuring and drawing ofpul

    戶提供的規格型號帶輪內孔鍵槽寬度等尺寸為用戶繪制帶輪圖紙也可為用戶提供測繪
分享友人
分享到 Line

分享到臉書