輪齒修形 的英文怎麼說
中文拼音 [lúnchǐxiūxíng]
輪齒修形
英文
geartooth correction-
( 4 ) the modification theory is deduced in the condition of preserving the motion state of the end face harmonic gear drive of oscillating teeth
（ 4 ）在分析活齒端面諧波齒輪傳動裝置運動狀態的基礎上，提出了端面齒輪、活齒和波發生器端面凸輪齒面的修形方法。Study on distributing construction of the sliding - tooth pump
修正齒形的復合齒輪泵流量特性This paper develops a mathematical model for the solution to the longitudinal tooth curve of an internal gear shaver based on the simplified principle for space transmission of a helical gear pair without flank clearance, and proposes a calculating approach of the profile modification of the grinding wheel to be used for grinding the longitudinal tooth curve of the shaver
摘要用簡化的空間螺旋齒輪作無側隙嚙合傳動的原理，建立了求解內剃齒刀齒向曲線的數學模型，並給出了修磨這種齒向曲線的盤形砂輪的廓形計算方法。Therefore, the suitable coefficient of engagement overlap got by profile correction and addendum modification is beneficial to the output property of the gear pump
因此，對齒輪齒形進行修形和變位修正使齒輪得到合適的嚙合重合系數有利於改善齒輪泵的輸出特性。The paper offers a viable method for the detection and evaluation of spiral bevel gears. this method can offer reference for amending of the gear tooth surface, and possesses important scientific and applied value for actual design and manufacture
本文對航空弧齒錐齒輪副嚙合質量的檢測與評估提供了一種可行的方法，並能為齒面的修形提供參考依據，在實際設計和製造過程中有重要的科學與實用價值。The pump gears with large module and less number of teeth are adopted by the high viscidity gear pump. when they are in mesh, meshing interference happens. in order to avoid interference of flank, tooth profile is modified
高粘度齒輪泵中的泵齒輪通常模數大，齒數少，它們嚙合時常發生干涉，為了消除嚙合干涉，需對泵齒輪進行修形。Firstly the reason of interference of flank is analyzed and contact ratio and overlap ratio and the point of profile modification are calculated according to two conditions
本文首先分析了齒輪發生嚙合干涉的原因，並分兩種情況計算了了齒輪的重合系數和修形位置。On the basis of relationship between meshing rigidity and noise and taking the modification, vibration deduction and noise dropping as the aims, the tooth profile modification was carried out on spur bevel gar by the use of revolving involute curve
摘要根據嚙合剛度和噪聲之間的關系，以修形減振降噪為目的，用旋轉漸開線曲線對直齒錐齒輪進行齒廓修形。Adopting the precision cold forging to carrying out the tooth profile modification of spur bevel gear evidently lowered the cost, thus provided a kind of new researching method for the modification, vibration reduction, noise dropping and design of the gear transmission system
直齒錐齒輪採用冷精鍛進行齒廓修形，顯著地降低了成本，這為齒輪傳動系統的修形、減振、降噪和設計提供了一種新的研究方法。Domestic and abroad standard and test information of alimak co. for braking distance of antifalling safety device of construction hoist are analyzed. the writers study the application and inspection situation of safety device in our country and put forward a suggestion of reasonable range of braking distance for safety device with gear cone drum
本文分析了有關施工升降機防墜安全器制動距離的國內外標準條文和alimak公司的試驗資料，結合我國施工升降機防墜安全器的應用和檢測情況，提出了修改齒輪錐鼓形防墜安全器制動距離合格範圍的建議。The rationality of cycloid gear actual operating space is verified by optimizer, finally the conclusion of the isometric plus travel distance alter shape curve much more approach corner alter shape is obtained
通過編制的優化程序驗證了擺線輪齒形工作部分范圍的合理性，得出了等距加移距修形曲線更逼近轉角修形曲線的結論。The result of static calculation showed that the tooth profile long modification of spur bevel gear possesses better effects of vibration reduction
靜態計算結果表明，直齒錐齒輪齒廓長修形具有較好的減振效果。Research on wear - resistance and bending strength of modified tooth profile involute gear
修形齒輪耐磨性和彎曲強度的研究Therefore this study focuses on the output property of the gear pump after profile correction
本文針對這一現狀，研究了齒輪修形后齒輪泵的輸出特性。分享友人