輸入桿 的英文怎麼說

中文拼音 [shūrùgǎn]
輸入桿 英文
input lever
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 入 : Ⅰ動詞1 （進來或進去） enter 2 （參加） join; be admitted into; become a member of 3 （合乎） conf...
  • 桿 : 桿名詞（桿子） pole; staff
  • 輸入 : 1 （從外部送到內部） import 2 [電學] input; entry; entering; in fan; fan in; 輸入變壓器 input tra...
  1. The circuit identification of planar single - input - dyads mechanism ( sidm ) is studied

    研究平面單輸入雙桿組連桿機構（ sidm ）迴路識別問題。
  2. Based on the hydromechanics principle, the hydraulic equipment can push compressive oil into actuators by the pressure and direction control circuits. the piston of actuator translates distributed pressure into centralized force of piston rod

    液壓加載根據液壓流體力學原理，利用液壓元件組成的壓力和方向控制迴路，將一定壓力的油液輸入液壓缸，由液壓缸內的活塞把分佈的油壓轉變為集中力，最後經活塞桿輸出。
  3. Input devices include keyboards and pointing devices such as mouse, joystick, track ball, or light pen

    輸入設備包括鍵盤和點擊設備如鼠標，操縱桿，跟蹤球或光筆。
  4. However, due to the elastic deflection and vibration of the links, the flexible manipulator becomes an infinite dimension mimo system with distributed parameters, and is highly nonlinear and strong coupling. therefore, the model and the control of flexible manipulator are of great significance both in theory and in application

    然而也正是由於連桿存在彈性變形和振動，使得柔性機械手成為一個高度非線性的、分佈參數的、強耦合的無窮維多輸入多輸出系統， ，因此其建模和控制也具有重要的理論意義和應用前景。
  5. The results showed that : ( 1 ) the models used by author and the analysis are useful and can be practiced. ( 2 ) after using isolation technology, the structure ' s period, earthquake response, base shear force and acceleration are all decreased markedly and the horizontal displacement focuses on isolation layer. ( 3 ) under frequent earthquake action, the shear force ratio between layers is close to 0. 35 ; in according with the provision in aseismic design code that the horizontal seismic reduction coefficient can choose 0. 53 and the upper building can be designed by decreasing one degree

    計算模型分別採用三維空間模型及規范中建議的彈簧、質量模型，隔震層採用疊層橡膠隔震支座，運用大型結構有限元計算程序sap2000以及自主開發的nba結構程序計算隔震結構在多維地震動輸入下的動力非線性時程反應，同時研究了隔震結構在溫度變化的作用下，結構各桿件的內力變化，通過對變電建築物在傳統抗震作用下及隔震作用下的分析比較，得出一些有益的結論。
  6. The design process of the proposed method is described as follows : the input of the method is the 3d sketch of a light steelwork, and the geometry and topology information of the members in a steelwork are established automatically. the steel types and function of the linked members are determined by means of interactive scheme according to the design requirements. and the arrangement of the steel members and their orientation are built according to the steel member ' s type, the function of the steel member, the knowledge of the steelwork and welding technology

    在該方法中，首先通過交互手段輸入輕型鋼結構的三維線框簡圖、自動確定結構的幾何和拓樸信息，根據設計要求輸入各桿件的型鋼類型和在結構中的功能；然後，根據型鋼類型、桿件功能、鋼結構設計知識以及焊接知識自動確定桿件的搭配關系、建立桿件的方位布置確定規則和節點板設計的規則；最後，利用這些規則來決定節點稈件連接關系、連接位置，確定節點板的類型、布置方位和位置，實現三維鋼結構的結構自動設計。
  7. The design process of the proposed method is described as follows : the user inputs the 3d sketch of a welded machine, and the geometry and topology information of the members in the welded machine are established automatically. the design information is acquired by the means of man - computer interaction. according to the knowledge of design and welding, the rules of bar orientation, joint processing and welding sequence are established

    用戶在autocad中輸入焊接機架的線框簡圖，提取出機架結構的幾何和拓撲信息，然後通過人機交互輸入設計信息，並根據機架的設計知識與焊接知識，建立機架的桿件方位布置規則、節點處理規則與焊接順序自動確定規則，最後在autocad中生成經過節點處理的機架三維實體，並提供一套合理的焊接順序。
  8. Thirdly, it simulated the pumping circuit & dividing circuit with the widely used software matlab / simulink. the displacement of the rod piston and the impact of hydraulic are analyzed in the different input flow ( frequency of pump ) and different reversing time. it found out the cause of hydraulic impact ( one - to - one incorrespondence between the response time of dividing circuit and the operation time of rod piston ), and gave some methods to weaken hydraulic impact. in the final part of the paper, the reliability of the theory analysis is further verified by the experiment of hydraulic system

    首先在流變學原理的基礎上，深入分析混凝土在輸送管道內的流動狀態，得出混凝土泵的負載特性方程；然後根據功率鍵合圖的建模方法，建立泵送迴路和分配迴路的數學模型，並運用模擬軟體matlab simulink對泵送和分配迴路模型進行了模擬，分析了在不同的輸入流量（泵送頻率）和換向時間下，活塞桿的位移和系統的液壓沖擊情況，找到了引起液壓沖擊的根本原因（即分配迴路的響應時間（固定值）與活塞桿的運動時間（變化值）不相匹配） ，並提出了相應的改進方法。
  9. At last, a software about the jrs and workspace is developed in virtue of vc + + with which we can easily obtain the jrs of both side links and workspace of coupler points in any configuration mode of mechanism only if we input the dimensions of a five - bar mechanism

    最後，用vc + +開發出一個軟體平臺，只要輸入任意一個五桿機構的尺寸參數，就可以知道該機構在各種裝配模式下的兩連架桿的轉角空間及連桿點的工作空間。
  10. The results show that the electron mean drift velocity is affected by the cathode radius, the impedance of the load diode, the inner radius of vanes and the input voltage

    結果表明電子平均漂移速度決定於陰極桿半徑、負載二極體阻抗、陽極慢波葉片內徑和輸入電壓。
  11. Finally by use of c + + and opengl, the practical simulation system software has been developed, which makes control manufacture combined with the whole complex screw pole manufacture process such as parameter input, design and selection of milling cutter, interference judgement, interpolation computing, three - dimension simulation and numeral code, in order for the guide of theory research and manufactural practice

    最後利用c + +和opengl設計並實現了較實用的軟體模擬系統，使整個復雜螺旋桿的加工過程從參數輸入、刀具設計選擇、干涉判定、差補計算、三維模擬到數控程序生成和控制加工有機地結合起來，以期對理論研究和加工實踐起到指導作用。
  12. This paper presents a simulation test control system of an airplane engine operating system, which control motor to simulate the force and velocity of throttle lever and the torque on axis

    本文闡述了某型飛機發動機操縱系統地面模擬試驗控制系統，它主要控制力矩電機去模擬油門桿上的速度和力以及模擬發動機輸入軸的力矩。
  13. In this thesis, an algorithm based on multiple features for recognition of escherichia coli promoter was proposed. firstly, word frequency method was utilized to extract the content ’ s information of a given sequence, and position weight matrix and hidden markov model were applied to analyze the information on structure, and then this information was input into a classifier

    本文提出了一種基於多特徵的大腸桿菌啟動子判別演算法，即通過詞頻分析獲得序列的組成特徵，利用位置權重矩陣（ pwm ）和隱馬爾科夫模型（ hmm ）獲得序列的結構特徵，然後輸入到一個分類器中進行分類。
  14. A port tyre crane has various parts and complex structure, which is made up plenty of beam - bar and shell elements, manual calculation can not guarantee the precision while finite element method needs onerous structure modeling and a great deal of date input. the finite element analysis and modeling of the port tyre crane are difficult because of complex structure and various loads. in order to fit further more design and exploitation of the same type as well as the upgrade of the production i study a kind of parametric software for structure analysis of the port tyre crane, it can reduce the difficulty of modeling and structure analysis as well as improve efficiency

    港口輪胎式起重機部件繁多、結構復雜，由數目眾多的梁桿與板殼組成，其結構設計和力學分析使用傳統的手工計算方法難以保證精度，有限元方法則需要繁重的結構建模和大量的數據輸入，並且要求分析人員具有相當的力學知識和有限元基本理論。港口輪胎起重機結構的復雜性、載荷工況的多變性導致港口輪胎起重機結構有限元建模和分析工作效率低、難度大。針對這種情況本課題研發了一套港口輪胎式起重機結構的有限元參數化分析軟體，以適應同類機型的進一步設計開發和產品升級換代，降低建模和分析的工作難度，提高工作效率。
  15. This mechanism generates the linear motion from the rotation from the input end ( the lever at the bottom ), and path of the process can also be changed by clutched

    此機構的目的是靠輸入端的圓周運動產生輸出端（下方直桿）的直線運動靠著換檔的動作可以改變直線運動的行程。
  16. The work of this dissertation is mainly as follows : 1. systemically introduce and evaluate the advance of studies on damage models of reinforced concrete on material, member and structure level ; 2. by inputing earthquake wave for member model, analyse dissipating energy process and development process of structure damage and discuss relation between structure damage and pga, time of earthquake motion

    本文的主要內容如下： 1 ）系統地總結當前鋼筋混凝土損傷理論在基於材料、構件和結構層次的研究進展及其評價； 2 ）通過桿系模型對結構輸入實際地震動，分析結構在地震作用下能量耗散過程以及結構損傷的發展過程，並討論結構損傷和地震動三要素（主要是加速度和持時）的關系。
  17. The input sub - system should take all input ( keyboard, mouse, gamepad and joystick ) and unify it and allow for abstraction of control

    輸入子系統負責處理所有的輸入（鍵盤、鼠標、游戲手柄和游戲搖桿） ，並把它們統一起來以允許控制的抽象化。
  18. As for the problems in the experimentation, such as the slow response speed of axes torque control, the disturbance of torque control to position control of throttle lever and the torque fluctuation of axis, solutions had been put forward and proved theoretically

    對于試驗過程中出現的以下問題，油門桿高速運動中輸入軸力矩控制的響應速度較慢，輸入軸力矩控制對油門桿位置控制的擾動，以及輸入軸力矩脈動現象，提出了解決方法，並且從理論上加以驗證。
  19. For example, a joystick can be used to select guiding texts or functions. since the screen usually follows that of the input device, the matrix format is flexible and can be used for a matrix of any rectangular shape

    「全方位搜索系統」不限於鍵盤輸入，例如游戲桿也可用作選擇文字或功能向導。由於筆觸式螢幕同時也是輸入設備，使「全方位搜索系統」可隨時重新定義矩陣結構。
  20. Layout input pole length ' s locus when the mechanism follows kadang movement in two ways. one is multinomial curve locus and the other is linearity intermixed by parabola curve locus. we study the displacement > velocity and acceleration curve consulting time under variety velocity characters, and get the best curve and the best velocity character, which will have a very important significance for kadang movement ' s input control of this mechanism

    對卡當運動輸入桿件的伸長進行了軌跡規劃，採用了多項式與混有拋物線的線性函數作為規劃軌跡，研究了不同速度參數條件下的位移、速度、加速度的時間變化曲線，給出了最優曲線和最優速度，這對于機構卡當運動輸入控制的實現和優化具有重要意義。
分享友人
分享到 Line

分享到臉書