轉輪輪轂 的英文怎麼說
中文拼音 [zhuǎnlúnlúngū]
轉輪輪轂
英文
impeller hub-
We mainly produce shifting fork and release fork of large - scale and heavy - duty truck ; shifting fork, release fork, shifting block, choosing - gear shaft, reverse - gear shifting fork shaft, right - and - lfet steering joint arm, upper cross arm shaft, wheel hub, link rod of all kinds of cars right - and - left supports, nipbutton of train auto - girder parts ; centeral wedge, fixed lean - board of absorber ; shifting fork, erankshaft, link rod, under - link board, startup pole of motocycle ; mould forging of mine, construction machinery, textile machinery, non - ferrous metal industry, etc
主要生產產品：大、重型卡車變速箱的撥叉、分離叉等；各種轎車變速箱的撥叉、分離叉、撥塊、選檔軸、倒檔撥叉軸、左右轉向節臂、上橫臂軸、輪轂、聯桿，火車自動梁部件的左右支柱、夾扣，減震器的中心楔塊、固定斜板等鍛件；摩托車的撥叉、曲軸、連桿、下聯板、啟動蹬桿總成；礦山機械、建築機械、紡織機械、有色金屬等精模鍛件。Compress disk is the very important rotational component in the areoengine. when the compress disk is working, the grads of temperature and stress between the rim and the center of the disk are great. in order to raise the thrust - weight ratio of the disk and reduce oil consumption. the best prospective way is the dual alloys disk used
壓氣機盤是航空發動機上一個很重要的轉動部件，壓氣機盤工作時，輪緣和輪轂溫度梯度和應力梯度較大，為了提高飛機發動機推重比、減低耗油量，要求壓氣機盤的工作溫度、使用性能更高，雙合金盤製造是最有發展前景的技術。The complex vortex system structure and shock wave system structure inside this rotor is obtained. wall flow patterns on the blade surface and hub surface are found out. the complex vortex system structure, such as horseshoe vortex, passage vortex, corner vortex and trailing vortex, and the interaction with shock wave system are researched. especially, the character of the tip clearance flow inside the rotor passage is revealed, and the interaction between shock wave and tip clearance flow near blade tip and the evolution of tip clearance flow are considered
給出了葉片表面及輪轂面上的壁面流型，分析並揭示了轉子葉道內的馬蹄渦、通道渦、角渦、尾渦等復雜渦系及其與激波的相互干涉；特別是，分析並揭示了轉子葉道內頂隙射流的特點，得到了頂隙附近激波與泄漏流動的干涉形態及泄漏流動的發展，並著重給出了其與激波的干涉形態。Main part is to point to internal - combustion engine airframe, air cylinder housing of casing of lid, flywheel, frame, gear - box, axle shaft, steering gear housing, poor fast implement housing of hub of casing of housing, final drive - box, apply the brake, towing plate, promotion
主要部件是指內燃機機體、氣缸蓋、飛輪、機架、變速箱箱體、半軸殼體、轉向器殼體、差速器殼體、最終傳動箱箱體、制動轂、牽引板、提升殼體。For the model of flywheel rotor in the thesis, the weight of aluminum hub is 13. 5 kg, and the weight of composite rim is 14. 5 kg. moreover, the multi - ring s flywheel rim was made by filament winding process
本文提出的飛輪轉子模型，鋁合金輪轂重13 . 5kg ，復合材料輪環重14 . 5kg ，採用多環套裝纏繞工藝，分為內外兩層輪環，分別採用t300和m40j碳纖復合材料。Finally, based on the elasto - plasticity theory, plastic design and analysis for metal hub of flywheel was performed
最後，利用彈塑性理論，對飛輪轉子的金屬輪轂進行彈塑性設計與分析。Put the wheel hub on a turning device, make it whirl on the strength of one constant bending moment, make hub bear a whirling bending moment constantly
將輪轂置於一旋轉的裝置上，使其可在一恆定不變的彎矩作用下旋轉，使輪轂始終承受一個旋轉彎曲力矩的作用。分享友人