速效顯影液 的英文怎麼說

中文拼音 [sùxiàoxiǎnyǐngyè]
速效顯影液 英文
quick-acting developer
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 顯 : Ⅰ形容詞1 （明顯） apparent; obvious; noticeable; evident 2 （有名聲有權勢的） illustrious and inf...
  • 影 : Ⅰ名詞1 （物體擋住光線后映出的形象） shadow 2 （鏡中、水面等反映出來的物體形象） reflection; image...
  • 液 : 名詞（液體） liquid; fluid; juice
  • 速效 : quick results; quick acting速效肥料 quick acting fertilizer; active fertilizer; readily available...
  • 顯影 : [攝影學] develop
  1. The primary results showed : using m199 as diluents containing 20 % bovine serum, it is better to freeze the cells slowly freezing at fist then increase freezing speed ( for example, from 0 to - 6 freezing speed is about - 0. 05 a minute, from - 6 to - 40, freezing speed is about - 0. 5 a minute ), studies on effect of various concentration of dmso demonstrate that about 12. 5 % dmso gave the highest post - thaw percentage of viable cells. the concentration of bovine serum had no different effect on the percentage of the viable embryo cells of misgurnus auguillicaudatus. the embryo cells derived 6 from the later stage of blastula offish is more resistant to the cryogen than the cells of early stage of blastula. the cells preserved in liquid nitrogen at - 196 were thawed and cultivated, a few cells were found adhere to the surface of culture vessel when the percentage of viable cell was more than 30 %. the cells in only two culture vessels were found to proliferated and gave rise to many small morphologically undifferentiated cells

    研究初步表明:以細胞培養液m199 （含2既的小牛血清，常規量雙抗）為凍存稀釋液對泥鰍胚胎細胞冷凍保存宜採取先慢后快的方式（例如，從0一一6 ，凍存速度為一0 . 05 / min ，再以一0 . 5 / min的速度從一6一一40 ） ; dmso的保護效應濃度為12 . 506左右;小牛血清的濃度對泥鰍胚胎細胞的成活率影響不明顯;囊胚晚期細胞抗凍性比中早期強;通過對不同批次的凍存細胞解凍培養，解凍后成活率為30 %以上細胞培養數天後均有少數細胞貼壁，但只發現兩瓶培養細胞有明顯增殖現象產生許多未分化的小細胞。
  2. By comparing the dry plate pressures drop and distributions of velocities simulated on single valve with those of double valves, it was found that there was intense turbulence in the flow fields around fixed - valve, there were eddy areas between valve side orifices and tray wall, there were eddies above the valves too, these led to the complex behaviors of gas perforating valve, these had a great effect on the gas - liquid mass transfer process. at the same time, in order to prevent the disadvantageous effect of gas between one valve with another on the gas - liquid mass transfer, it was very effective to change the fields of gas perforating valve by folding the edges of valve

    通過對數值模擬得出的單閥和雙閥塔板的干板壓降及流場速度分佈分析對比后發現，固定閥周圍流場存在較強的湍動，閥側孔與塔板壁面區域以及閥體的上方空間存在明顯的渦流區，使氣體穿閥后的行為變得復雜，並對氣液傳質過程產生重大影響；模擬結果表明，為防止和削弱固定閥間的對沖造成的「死區」對傳質帶來的不利影響，通過折邊來改變氣體的氣路是非常有效的，模擬值與實驗值基本得到吻合。
  3. With experiments and theoretical analyzing, we find when the heat discharge is smaller than the entrainment limited, what influences the ability of heat - transmitting of work quality is the quantity of injection and dry limit fluid inventory, the optimum quantity of injection of the three working fluid is 8 ~ 14g ; and the delivering factor that transmission coefficient is determined by capillary limit, not the heat transmission ability of the thermal syphon. therefore, among the three working fluid, acetone is the best. low wind - speed has the obvious function in heat transmission of the thermal syphon

    本文通過實驗研究和理論分析，認為在熱流量小於攜帶極限時，影響工質傳熱能力的是cpu重力熱管的充液量和其乾涸極限，此次所實驗的三種工質，最佳充液量應當在8g ~ 14g ；傳輸因素主要決定普通熱管的毛細極限，而不是重力熱管傳熱能力的決定因素；三種工質中的最佳工質是丙酮；小風速時風速的變化對cpu重力熱管的傳熱有明顯的作用，但在風速大於1m / s以後，風速增加對于cpu重力熱管的傳熱能力的增加效果減緩。
  4. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
分享友人
分享到 Line

分享到臉書