連軋機 的英文怎麼說
中文拼音 [liányàjī]
連軋機
英文
[冶金學] tandem mill-
It is made up of the melting shaft furnace, titled holding furnace, ( reverberatory refining furnace ), casting machine, automatic shearer, cast bar straightening and dege shaving machine, rolling mill, engine oil lubrication system, emulsion lubrication system, rod orbital coiler, line electric control, etc
銅桿連鑄連軋機生產線主要有融化豎爐,傾動式保溫爐, (銅精煉反射爐) ,連鑄機,滾剪機,校直刨邊機,打毛機,連軋機,潤滑油系統,乳化液系統,銅桿還原冷卻裝置,雙筐梅花收桿機和電氣控制系統等組成。Application of loopers in small section continuous finishing mill unit
活套器在小型精連軋機組上的應用The 1450 hot strip mill of panzhihua new steel & vanadium limited company has built in 1993, it is the important plates processing mill of pangang
攀枝花新鋼釩股份有限公司熱軋板廠1450熱連軋機組於1993年投產,是攀鋼重要的板材加工廠。Dynamic study on main drive system of hot continuous strip mill
熱帶鋼連軋機主傳動系統的動態研究Continuous casting and rolling line
連鑄連軋機組Analytical study on lubrication states and velocity in aluminum foil rolling process
冷連軋機成品板面粗糙度控制技術的研究Discussion on application of splitting rolling technology on horizontal continuous mill
水平連軋機組應用切分軋制技術的探討The continuous rolling machine has a function of automatic feeding and rods stacking stop
連軋機具有主動喂料和堆桿停車功能。Discussion on pass design of continuous mill for small section steel in hefei iron and steel group company
合鋼小型連軋機孔型設計探討Splitting rolling technology used in small section continuous mill of shuicheng iron and steel company
切分軋制技術在水鋼小型連軋機的應用The result of simulation the model and parameters are correct. it ensure the whole p ' roject being finished successfully
這也為整個冷連軋機軋制過程動態模擬項目的順利完成提供了保證。Because of the intrinisic characteristic of this kind of mill, it takes the plate as the main product, sometimes prodces the coils
這是由於爐卷軋機本身的固有特點,使其生產帶卷不如用熱連軋機更好。3 a set of 650 mm four - stand continuous rolling machine with annual output of 30 thousand tons. it may produce silicon steel and carbon steel coils whose sizes are 5 tons in weight, 0. 5mm in thickness and 510mm in width
3 650mm四機架連軋機組一臺套,年產量3萬噸,該設備可生產卷重5t ,厚度0 . 5mm ,寬度510mm的硅鋼普碳鋼卷。The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product
摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理,由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。According to the work condition of one 1450 five - stand tandem cold mill, reduction distribution as decision variable, the penalty function was established, in which rolling pressure distribution ratio was as objective function and the constraint condition of reduction distribution was as penalty term
根據某1450五機架冷連軋機生產工況,以壓下量分配為自變量,以軋制力成比例分配為目標函數,將壓下量分配的約束條件作為懲罰項,建立懲罰函數。Abstract : this dissertation introduces simply the principle of differential drive, and application of the principle in the small and middle continuous mills, which shows that the technology of differential drive in continuous mill can tally with present situation of our country metallorgica industry
文摘:介紹了差動調速的原理及其在中小型連軋機組中的應用,表明了差動調速連軋技術符合我國冶金行業的現狀。Abstract : in the operation beginning of the tandem rolling mill reduction gears being overhauled, the magnitude of the vibration is t oo large. this paper introduces a method of the vibration diagnosis of the reduct ion gears and explains the fault cause. it is proved that the conclusion is corre ct when the failure parts are replaced
文摘:針對連軋機組減速機在檢修后開始工作中,產生較大振動這一異常現象進行了診斷與分析,從而找出了產生這一故障的原因,更換故障件后得到證實,診斷是正確的According to the special characters of a multi - roll cold tandem mill, a rolling force prediction model based on fuzzy algorithm and cerebellum model articulation controller ( cmac ) combined with the traditional model was designed to improve the precision of rolling force prediction
摘要針對寬帶鋼多輥冷連軋機組特點,為提高軋制力的預報精度,在結合傳統軋制壓力模型的基礎上把模糊演算法和神經網路有機結合,設計出基於模糊小腦模型神經網路的多輥冷連軋機軋制力預報模型。By comparing the values of the traditional rolling force model and the prediction model by cmac with the measured ones, the precision of the prediction model by the fuzzy cmac is much better than that of the traditional rolling force model and is more suitable for online use of a multi - roll cold tandem mill controlled by computer, which also meets manufacturing requirement of the field and receives better control effect of the shape and thickness
通過對傳統軋制力模型計算值、小腦模型預報計算值與實測值進行對比分析可知,基於模糊小腦模型神經網路的多輥冷連軋機軋制力預報模型具有較高的計算精度,更適合於多輥軋機在線計算機過程式控制制的應用,滿足現場在線生產的要求,取得良好的板形板厚控制效果。Based on shanghai bao steel co. practical project, which is modeling 、 simulating of dynamic rolling procedure and control optimizing for cold continuing roll mill, the research of control optimization on the dc motor speed control system is studied
本課題結合上海寶鋼集團公司「冷連軋機軋制過程動態模擬及控制優化」項目,對直流電機速度控制進行控制優化研究。分享友人