進給輥 的英文怎麼說
中文拼音 [jìngěigǔn]
進給輥
英文
feed rolls-
A new system of rapid roll carriage infeed and return, together with automatic selection of pressure and feed rate, has improved the already impressive floor - to - floor times achieved
快速輥子進給和返回系統和自動壓力、進給速率調節器提高了工作效率。Take puts the winding up roller as the research object, has made the detailed analysis to its state of motion and a program scheme for calculating the tension control torque was provided
以放卷輥為研究對象，對其運動狀態作了詳細的分析，進而給出了計算控制力矩的程序框圖。Abstract : this article presents an analysis of the contact stre ss of rolls in two - cross - roll straightener and gives a method for the calculat ion
文摘:在實踐的基礎上對二輥矯直機輥面接觸應力的計算進行了理論分析，給出了輥面接觸應力的計算方法。Direct drive of the application rollers, separate direct drive of the doctor rollers, precision glue dosing due to speed difference between application and doctor roller
施膠輥直接驅動，配輥單獨驅動，根據施膠輥和配輥之間不同的進料速度精確給膠。A new method, which named reverse shrinking surplus method, has been pointed out based on the fem in order to optimize the speed curve of the spindle
摘要在基於有限元數值模擬的基礎上提出了反向最小余量法，用以優化芯輥進給速度曲線。The optimized speed curve can bring a steady press - down dimension in the process of the ring rolling which could assure high quality products
優化后的芯輥進給速度曲線能保證輾擴過程中始終有理想的每轉壓下量，從而降低缺陷的發生，提高零件質量。Abstract : the paper has undertaken an experimental investigation on theresistance coefficient of belt conveyor, base on the influence factors analysis of the main resistance of the belt conveyor, using belt conveyor resistance test bench and provided the function relations and coefficients of the resistance that varied linearly with the belt velocity according to the experimental results. the conclusion can be adopted for a belt conveyor design and dynamic analysis
文摘:在對影響帶式輸送機主要運行阻力的因素分析的基礎上，採用帶式輸送機運行阻力實驗臺對托輥運行阻力系數進行了實驗研究，根據實驗結果給出了運行阻力隨帶速線性變化的函數關系和系數，此結果可用於帶式輸送機設計和動態分析。And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array
本文採用ansys / ls - dyna計算程序為分析工具，對鋸齒形雙金屬復合板成型過程進行計算機數值模擬，在對軋制過程模擬時，針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題，給出了在ansys / ls - dyna中相應的解決方法：應用nodetosurface接觸方式，設定相應參數，選用雙線性等向硬化模型，載荷作為array施加在剛體質心。There are two feeding rotors near the inlet of heavy - duty crusher
在重型破碎機的進口附近有兩個給料輥。分享友人