邊界修補 的英文怎麼說

中文拼音 [biānjièxiūbǔ]
邊界修補 英文
edge patch
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  • 界 : 名詞1 （相交的地方; 劃分的界限） boundary 2 （一定的范圍） scope; extent 3 （按職業、工作或性別等...
  • 修 : Ⅰ動詞1 （修飾） embellish; decorate 2 （修理; 整治） repair; mend; overhaul 3 （寫; 編寫） write;...
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 邊界 : boundary; frontier; border; borderline; edge range line; periphery
  1. Further more, this algorithm also provides the criterion distinguishing edge inflexion and sleek curve section and the method computing inaccurately curvature radius and approximate perimeter. the paper also introduces the use method with cell edge hollow repairing and overlap or conglutination cell segmentation. for example, this algorithm has proved high - speed and has a good effect of cell segmentation on more than twenty groups of conglutinate and absent cells which are gathered from three kinds of cells

    同時給出了利用這些參數判別邊界角點，邊界光滑段的判據，以及估算曲率半徑，等效周長的方法;最後，以細胞邊界凹陷的修補和重疊細胞粘連的分割為例驗證了演算法的可行性，該演算法在採集到的30餘組粘連和缺損細胞上進行了驗證，結果表明，該演算法處理速度快，分割效果良好。
  2. It is difficult to estimate indent depth in theory. this paper presents two methods to estimate the relationship between dent depth and contact force, respectively amend method and deflection compensate method, which are developed by using a clear geometrical relation to express indent, incursion profile and deflection difference

    本文以一種新的觀點，用一個明確的幾何關系來確定壓痕、壓頭與板的接觸面剖面及接觸中心點與邊界點之間的撓度差三者之間的關系，提出兩種近似預測接觸力與壓痕深度關系的方法? ?修正法和撓度補償法。
  3. In this thesis it was proposed to simulate the drawing, trimming, flanging by using error - adjustment method. the initial trimming lines would be adjusted and optimized in the computer by adjusting error. if the shape error between the flanging boundary line and the target is larger than prescribed, the redundant area is subtracted from the initial blank by some amount of volume along the deformation path, and the insufficient volumes are added to the initial blank by the same amount

    本文提出，利用基於變形路徑的誤差修正法（ error - adjustment ） ，結合cae技術將對初始修邊線的調試過程在計算機中進行模擬（包括拉延、修邊、翻邊、整形等）計算，通過控制翻邊后零件成型邊界與實際目標輪廓之間的尺寸誤差來優化修邊線，如果初始切邊、翻邊后的輪廓與目標體的邊界存在較大偏差，則初始切邊輪廓中多餘部分單元將沿其變形路徑以相同體積量被切除，不足部分則沿其變形路徑以相同體積進行補償。
  4. So, the research of cad model reconstruction from scattered point cloud should be carried out urgently. the main key techniques contents of surfaces reconstruction from scattered point cloud data include data pre - processing, such as denoising data 、 filling holes and simplifying data, segmenting data, producing quadrilateral domains, and fitting b - spline surfaces

    本文直接以測量獲得的散亂點雲數據為對象，研究了點雲數據的幾何特性計算、平滑處理、孔洞修補、數據簡化等，在此基礎上，進一步研究了點雲數據分塊、四邊界區域劃分及曲面擬合。
  5. The research results include the follows : present some rules for selecting measuring method according to the characteristics of product, study some problems in data preprocessing such as noise removing, probe radius compensation, edge data extracting, sun - regions merging, and local data mending or re - sampling etc. to ensure the part cad models being built and assembled accurately at dimension and shape in re modeling application, three kinds of model modifying techniques are presented such as model - based modifying, drawing - based modifying and physical model - based modifying

    這些問題包括：根據產品表面形狀及建模方法，提出了一些選擇測量方法的原則；研究了消除測量數據噪聲信號、 cmm測頭半徑補償、測量數據邊界處理、測量數據塊拼合、數據補缺與補測等測量數據預處理問題。為了解決復雜外形產品re建模經常遇到的零件cad模型配合問題與尺寸精度、形狀精度問題，作者研究了基於cad模型的修正、基於零件圖樣的修正、基於物理模型的修正等三種模型修正技術。
分享友人
分享到 Line

分享到臉書