邊部缺陷 的英文怎麼說

中文拼音 [biānbùquēxiàn]
邊部缺陷 英文
edge fault
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
  1. The annihilation of the octahedron voids at the tips of fpds was divided two processes : ( 1 ) the oxide on the void was removed by the out - diffusion of oi in the shallow region, especially the oi aroud the void and by the entry of the interstitial si atomics. ( 2 ) the void without oxide shrinked by emitting vacances and the migration of silicon atoms from edge to the bottom of void

    Fpds端部八面體空洞的消失分為兩個階段： （一）覆蓋在空洞各個內壁上的氧化膜由於高溫下矽片表面區域的間隙氧原子，尤其是空洞型缺陷周圍的間隙氧原子的外擴散及自間隙硅原子的進入，而逐漸變薄直至最終消失。 （二）無氧化膜的空洞，在高溫下發出一個個空位，同時八面體空洞周圍的自間隙硅原子不斷的從空洞的邊緣遷移至空洞的底部，使空洞逐漸變淺直至最後消失。
  2. Based on this milti - hierarchical model, application method for information organization of part is presented. chapter 3 proposes a new rule of arbitrary maximum angles of chord for triangulation and locale optimum, which avoides calculating angles of conventional methods in mesh simplification. moreover, with the introduction of arithmetical average windage concept, optimum method for the boundary mesh retriangulations is presented

    第三章針對曲面網格簡化操作過程中出現的空洞剖分問題，討論層次模型的網格優化方法，提出了基於弦內角最大準則的局部網格簡化方法；針對網格曲面上存在的曲折邊界缺陷，提出以邊界輪廓算術平均偏差作為邊界曲折程度評定參數的邊界平滑優化剖分方法。
  3. External defects : undercut, overip, arc pit, gas cavity in surface, crack in surface

    外部缺陷：咬邊、焊瘤、弧坑、表面氣孔、表面裂紋。
  4. Refractory products. measurement of dimensions and external defects of refractory bricks. part 2 : corner and edge defects and other surface imperfections

    耐火材料製品.耐火磚的尺寸測量和外部缺陷.第2部分:角邊缺陷和其它表面缺陷
  5. Non - destructive testing of steel tubes - part 4 : automatic full peripheral magnetic transducer flux leakage testing of seamless ferromagnetic steel tubes for the detection of transverse imperfections

    鋼管的無損檢驗.第4部分:檢測橫向缺陷用無縫鐵磁鋼管的自動全周邊電磁變換器漏磁檢驗
  6. Entropy of an image is to express the smoothness or homogeneity of the image. while computing in a local window, if there exist edges, the local image will not be homogenous, variation of the grayness will be sharp and the entropy obtained will be low. otherwise, the entropy will be high. given the threshold of entropy, it can be determined whether or not exist edges. because entropy operator is sensitive to noise, the effect is bad if it is directly used to detect edges. in view of the deficiency, the paper comes up with an edge detection method in which entropy operator is combined with noise removal. if the entropy computed is higher than the threshold, it will be necessary to determine whether it is caused by noise or by edges. thus edge detection and noise removal can be made at the same time. with this method satisfactory effect has been achieved by experimenting upon image with low ratio of signal to noise

    圖像的熵用來刻劃圖像的平滑性或均勻性.在圖像的局部窗口中計算時，如果窗口中存在邊界，則窗口中的圖像不均勻，其灰度變化急劇，計算出的熵小；反之熵大.設定熵的閾值，即可判斷是否存在邊界.由於熵運算元對噪聲很敏感，直接用它進行邊界檢測，效果很差.文中針對這一缺陷，提出將熵運算元與去噪相結合的邊界檢測法，如果計算出的熵大於閾值，要判斷是噪聲的出現所引起，還是邊界的出現所引起，這樣，邊檢測邊界邊去噪聲.用該方法對信噪比較低的圖像進行實驗，得到了滿意的效果
分享友人
分享到 Line

分享到臉書