配力鋼筋 的英文怎麼說
中文拼音 [pèilìgāngjīn]
配力鋼筋
英文
distribution bar- 配 : Ⅰ動詞1 (兩性結合) join in marriage 2 (使動物交配) mate (animals) 3 (按適當的標準或比例加以...
- 力 : Ⅰ名1 (力量; 能力) power; strength; ability; capacity 2 [物理學] (改變物體運動狀態的作用) forc...
- 鋼 : 鋼名詞(鐵和碳的合金) steel
- 筋 : 名詞1 (肌的舊稱) muscle2 [口語] (肌腱或骨頭的韌帶) tendon; sinew 3 [口語] (可以看見的皮下靜...
- 鋼筋 : concrete iron; concrete reinforcing bars; rebar; reinforcing bar; reinforced bar; reinforcing ste...
-
Thus the use of steel fiber reinforcement concrete in corbel can avoid complicated calculating in design, and the diminish difficulty of construction, at the same time when corbel ' s dimension can not be increased the reinforcement concrete corbel ' s ultimate load capacity and anti - seismic performance can be improved by the addition steel fiber into concrete. this method has become a kind of applied method and is highly concerned by the domestic and international academe and engineer group
因此,在配筋密集的牛腿中使用鋼纖維混凝土可以避免設計時繁雜的配筋計算、減小施工難度,同時在牛腿截面尺寸不能增大的情況下,可以通過加入鋼纖維來提高鋼筋混凝土牛腿的承載力和抗震性能,用鋼纖維加入鋼筋混凝土牛腿已成為一種實用方法受到了國內外學術界和工程界的極大關注。Finally, considering the request of the gfrp bars reinforced furan resin concrete electrobath, we designed the structure of the electrobath and use finite element method to analyse it. in the process, pre - stress also was considered. the result of use in practice indicate the properties of gfrp bars can meet the request of electrobath structure
最後結合玻璃鋼筋呋喃樹脂混凝土電解槽的設計與開發,對電解槽的配筋布置、結構尺寸進行了設計,用有限元方法對電解槽的整體結構進行了計算分析,並考慮了玻璃鋼筋預應力的影響,其設計計算結果已在玻璃鋼筋呋喃樹脂混凝土電解槽的實際生產中得到了應用,且使用情況良好。Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior
分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大,實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著,而連接端板厚度及剪力連接程度的影響則不是太顯著。Abstract : experimental researches on normal section ultimate fle xural strength of prestressed reverse - rib - slab with excessive steel bar were m ade, and according to chinese norm ( gbj10 - 89 ) and american norm ( aci ) in which s train harmony analysis method was adopted, its ultimate strength was calculated, these make us further realizse the ultimate flexural strength of prestressed r everse - rib - slab with excessive steel bar
文摘:通過疊合結構中預應力超筋倒肋薄板正截面極限承載力的試驗研究,分別採用規范gbj10 - 89中的受彎構件、偏心受壓構件的計算公式及美國aci規范中的應變協調分析方法計算了極限承載力,從而更清楚地認識了配有高強鋼絲的超筋倒肋板的極限承載力計算問題。Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield
摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果,指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段;討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響;提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議;最終給出了異型節點抗剪承載力的計算公式。The author redesigned the common concrete beams and carried out a comparative analysis to the existing beams according to the specification for design of reinforced concrete and prestressed concrete highway bridges and culverts ( jtj023 - 85 ), the specification for design of reinforced concrete and prestressed concrete highway bridges and culverts ( informal version for advices ) and relevant rules of its matching stipulations, light aggregate concrete bridge technology stipulations ( ( informal version for advices ) and on the basis of prestressed concrete theory. the thesis emphasized on the research of the variation of the concrete, prestressing tendon quantities, their spans, beams " height and their rigidity of both the designed beams and the existing beams, and obtained the quantitative results from above research
採用hslc置換梁體中的普通混凝土,並運用預應力混凝土理論,依據《公路鋼筋混凝土及預應力混凝土橋涵設計規范》 ( jtj023 - 85 ) , 《公路鋼筋混凝土及預應力混凝土橋涵設計規范》 (徵求意見稿)和與之配套編制的《輕骨料混凝土橋梁技術規程》 (徵求意見稿)的有關規定,對上述普通混凝土梁進行了重新設計並與既有梁進行了對比分析,得出了設計梁與既有梁在混凝土及預應力筋用量、跨度、梁高以及剛度等方面的變化情況,得到了定量結果。The results of the truss type src columns test is analyzed, and the aseismic behavior of src column is deeply studied. with the shaped steel in the column, the bearing capacity is largely increased
本文研究了空腹桁架式src柱的試驗結果,對src柱的抗震性能作了比較深入的探討,結果表明配置角鋼的桁架式空腹鋼骨的勁性混凝土柱,其抗震能力明顯高於鋼筋混凝土柱。Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied
本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點,通過對這些試件的靜力荷載試驗,重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素,包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋,以及混凝土板內縱向鋼筋配筋率等。Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋,分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模;拆裝式和液壓式兩種模板的設計、製作要求和使用方法;綜合考慮、優化混凝土配合比,混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝,蒸汽養護的方法和規定;應力應變雙控制確保預應力施工質量的施工技術;採用重物移運器有效移梁的施工方法;壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法,並可為以後類似施工作借鑒。By this means, nonlinear properties of concrete and steel bars, as well as stress redistribution near the orifice caused by concrete cracking, are not taken into account. furthermore, concrete cracking could not be well controlled by reinforcing bars
這種方法不能反映混凝土和鋼筋兩種材料的非線性性質以及混凝土開裂后引起的應力重分佈,並且不能有效地控制孔口的開裂,按照此方法計算的配筋量往往偏大。As for the simply - supported slabs, the influence of the specimen fire proof properties is tested under the different concrete intensified degrees, under the different thickness of cover and under the different concrete quota. as far as the three - span continuous slabs are concerned, a series of analysis are conducted, including the specimen internal force redistribution under the different fire condition, the specimen deformation properties, features of the specimen destroying mechanism and the fire proof capability under the various condition
對簡支板,考察了不同混凝土強度等級、不同的鋼筋保護層厚度、不同配筋率等對構件抗火性能的影響;對三跨連續板,考察了不同受火工況下構件的內力重分佈變化情況、構件的變形性能以及構件破壞機構的特點;分析了各工況下構件的抗火性能的差異。In this paper, on the foundation of synthesizing engineering practice and study result of planted bar technique by chemistry glue on the domestic and international, embedded experiment study and theories analysis are done about bonded anchor behavior of chemistry planted bar anchorage behavior in this paper, the experimental results of 32 pulling resistance test ( meiya z3530 ) are given, considering some factors to affect bonded anchor behavior of chemistry planted bar such as the strength of concrete anchorage lengths diameter of steel bar and holes thickness of the protecting layer confecting circumstance of the hoop bar and quantity of construction especially which is very easy to be neglected and so on, and bonded anchor mechanism failure mode load carrying capacity and slide behavior are analyzed in - depth
本文在綜合國內外化學膠植筋技術的工程實踐和研究成果的基礎上,對化學植筋的粘結錨固性能作了較深入的試驗研究和理論分析。文中通過32個化學膠(美亞z3530 )植筋試件的拉拔試驗研究,考慮混凝土強度、錨固長度、鋼筋植筋、鉆孔孔徑、保護層厚度、箍筋配製情況及施工質量等因素對植筋粘結性能的影響,特別是植筋的施工質量對粘結性能的影響是比較容易被忽視的因素,對化學植筋的粘結錨固機理、破壞形態、承載力及滑移性能作了比較深入的剖析。As a new variety of steel wire in our country, the mid - strength ( 1270mpa ) spiral - ribs steel wire has many excellences such as high strength, good ductility, credible felting and anchoring capability witn concrete and so on. the pre - stressed concrete slab with this sort of steel wire has good mechanical property. so it is an ideal substitute to the cold - processed wires traditionally adopted in pre - stressed concrete slabs
中強( 1270mpa )螺旋肋鋼絲是我國研製開發的預應力鋼筋新品種,具有強度高、延性好、與混凝土粘結錨固可靠的優點,以這種鋼絲為配筋的預應力空心板具有良好的力學性能,是傳統用於預應力混凝土空心板的冷加工鋼絲的理想替代品。Secondly, the basic principle on optimal design of structure is presented. based on the characteristics of aqueduct - stayed optimal design, cable optimization, aqueduct body selection optimization and aqueduct body vertical section optimization are included. the prestresses of cable - stayed, the dimension of aqueduct and the number of reinforcing steel bar are chosen as the design variables
根據斜拉式渡槽優化設計的特點,本文將槽身優化分為索力優化、槽身橫斷面優化以及槽身縱斷面優化三個方面進行優化設計,確定斜拉索預應力、槽身斷面尺寸、槽身橫向及縱向預應力鋼鉸線配筋數量等槽身設計的主要變量。Through the comparative text of the four reinforced concrete frames braced with the eccentric steel, which have the same shapes, materials, dimension and the different brace form, several parameters of these frame behavior, such as side stiffness, limit load and energy consume ability, were studied. the limit state of these frames were analyzed
本文通過對四榀具有同一外形尺寸及配筋而具有不同型式的偏心角鋼支撐的鋼筋砼框架和一榀相同尺寸及配筋的鋼筋砼框架的對比性試驗,研究了上述結構的抗側剛度、極限承載力及結構的耗能等各項指標,探討了偏心角鋼支撐鋼筋砼框架結構的受力特點,並對其極限狀態進行了理論上的分析。For the cantilever beam, the theoretical stiffness and limited capacity are slightly less than the test ones if considering only the steel beam and the reinforced bars in the negative moment zone with the concrete in the tension zone ignored
結果表明:簡支組合扁梁,忽略彈性中和軸以下受拉的混凝土的影響,採用等效換算截面方法計算所得的剛度和極限承載力與試驗結果比較吻合;懸臂梁只考慮混凝土板中配置的負彎矩鋼筋,忽略混凝土,計算所得的剛度和極限承載力比試驗結果略微偏小,但相差不大。Then the coupling beams with new reinforcement layout were made an inquiry into, and the improvement on the seismic behavior by coupling beams diagonally reinforced with a few rows in end regions was found out at last, based on the observations of the experimental phenomena and the analysis of the measurement result, and by the comparison of seismic behavior by making use of hysteretic response, ductility and energy dissipation behavior, a conclusion is presented : the code for design and construction of reinforced concrete high - rise structures ( the draft asked for advise hi 2000 ) ca n ' t ensure that the coupling beams have fairly good seismic ductility ; the result of improvement of the seismic ductility of the coupling beams by the increase hi stirrups besides the strengthen of longitudinal detailing reinforcement was n ' t obvious ; the coupling beams diagonally reinforced with a few rows in end regions have fairly good mechanisms, and the ductility and the behavior of energy dissipation are better than conventionally reinforced concrete coupling beams, so it is suitable to te tised in short coupling beams
本文通過對三根小跨高比(均為l h = 1 . 0 )剪力墻洞口連系梁在低周反復荷載作用下的試驗,了解了嚴格按《鋼筋混凝土高層建築結構設計與施工規程》 ( 2000年徵求意見稿)設計的連梁具有的抗震性能,研究了採取增大連梁配箍量同時加強縱向構造筋的方案對抗震性能的影響,並進一步對新的配筋形式的連梁進行了探討,了解了在連梁梁端配置多排交叉斜筋方案對連梁抗震性能的改善。通過對試驗現象的觀察和量測結果的分析,利用荷載?位移滯回曲線、延性和耗能性能等指標對各個試件的抗震性能進行了比較,最後得出結論: 《鋼筋混凝土高層建築結構設計與施工規程》 ( 2000年徵求意見稿)不能保證小跨高比連梁具有較好的抗震延性:通過增大連梁配箍量同時加強縱向構造筋的方案對改善連梁的抗震延性的效果不太明顯;梁端配置多排交叉斜筋的連梁具有相對較好的受力性能,其延性和耗能性能等各項性能指標均優于普通配筋連梁,宜在深連梁中採用。Consequently, the precast components don ’ t need any interim falseworks to be supported in the mid - span as bottom forms when the laminated concrete lay is being placed. furthermore, to form two - way slabs, the transverse steels can be arranged through the rectangular cores in the ribs of the precast slabs as needed. it makes the construction of composite two - way slabs easier and more feasible, practical, and suitable to introduce and apply to the building construction on a large area
由於預制構件具有剛度大和承載力高的特點,施工時以預制構件作為樓板底模無需設置跨中臨時支撐;同時還能通過預制構件板肋預留的長方形孔布置橫向受力鋼筋實現樓板的雙向配筋,使預應力雙向疊合樓板的施工簡單易行,更適合於大面積的推廣應用,具有較大的工程應用價值。Considering the characteristics of internal force and structures of simply supported pc bridges, a novel automatically step - up method ( asum ), taking into account the influence of steel arrangement, steel ratio, stress losses of tendons and time - dependent concrete modulus, to analyze creep and shrinkage effects is presented. this method accepts all kinds of expressions of creep and shrinkage, and it is easy to calculate total stress, strain of concrete and steel and deflection of bridge at any time, the expected prediction accuracy will be obtained by further dividing the time - step within duration
首先,針對預應力混凝土簡支梁橋的受力特徵和構造特點,提出了徐變效應分析的全量形式自動遞進法,可考慮截面上鋼筋位置、配筋率、預應力鋼筋鬆弛、混凝土彈性模量隨時間變化等影響,且計算式可適用於任何形式的收縮、徐變特性表達式;建立的公式可方便地求解任意時刻混凝土、鋼筋的應力與應變和跨中梁體的豎向變形,計算精度可方便地通過計算時段的細分來控制,直至給出滿意的結果。Middle strength ( 1370mpa ) spiral ribs steel wires is a new type of high strength and good ductility and anchoring strength rolled steel, which is the ideal steel for the high effective pre - stressed reinforced concrete hollow slab. the slab with it has lower price than the traditional ones as well better mechanical property
中強( dw1370 )螺旋肋鋼絲是一種強度高、延性好、錨固性能優良的新型材料,是高效預應力空心板的理想的受力鋼筋,以這種鋼筋為配筋的預應力空心板不僅具有較好的力學性能,滿足現代建築市場對預應力空心板的要求,而且其價格比低於傳統的冷加工鋼筋。分享友人