配筋比率 的英文怎麼說

中文拼音 [pèijīnbǐlǜ]
配筋比率 英文
percentage reinforcement
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 筋 : 名詞1 （肌的舊稱） muscle2 [口語] （肌腱或骨頭的韌帶） tendon; sinew 3 [口語] （可以看見的皮下靜...
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 比率 : ratio; proportion; rate比率計 ratio meter
  1. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  2. The results indicate that the ratio of span to rise, the ratio of reinforcement and the stretching controlling stress are the three primary influencing factors to the failure pattern of the slab. in addition, the relationships between the ratio of deflection to span and the ratio of span to rise and the stretching controlling stress submit to linear curves, the relationship between the ratio of deflection to span and the ratio of reinforcement submits to a quadratic parabola curve

    運用數值分析程序計算了175組不同跨高比、配筋率、張拉控制應力的中強（ 1270mpa ）螺旋肋鋼絲預應力空心板，結果表明跨高比、配筋率、張拉控制應力是影響空心板破壞形態的主要因素，且構件撓跨比與跨高比和張拉控制應力呈線性關系，與配筋率呈二次拋物線關系。
  3. It shows that the method suggested in the paper is simple, applicable for engineering and has good precision. on the bases of the formulas deduced, and combining with relative test datas, it studies in the paper several factors influencing the bearing performance of the simple beams, such as shape of the external tendons, the equal moment segment length, span - to - depth ratio of the beam, valid initial prestress of the external tendons, area of the internal tension reinforcement, strength of the concrete, vertical distance between

    在公式推導的基礎上，結合相關試驗資料，研究了體外筋的形狀、等彎矩區長度、梁跨高比、有效張拉預應力、體內受拉筋配筋率、混凝土強度、錨固點到樑上邊緣在垂直方向上的距離、體外預應力筋水平段長度（雙折線型體外筋的情況）以及荷載類型等對體外預應力混凝土簡支梁受力性能的影響。
  4. Additionaily, the calculation method presented by specification for design of r. c. special shaped columns ( dbj / tl5 - l5 - 95 ) is discussed. in order to study the shear responses of special shaped columns, the ratio of tensile flexural steels " the ratio of moment and the shear - span ratio were analyzed

    為了研究異形截面柱的受剪性能，本文在總結已有試驗資料的基礎上，分別討論和分析了考慮受拉縱筋配筋率、彎矩比和剪跨比對異形截面柱受剪承載力的影響。
  5. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  6. Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model

    到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。
  7. By changing the parameters of stirrups ratio and axial load ratio, 6 high strength concrete ( hsc ) columns are tested subjected to cyclic lateral load. the baring capacity of hsc columns with new form of stirrups are compared with hsc columns with normal form of stirrups. load - displace relation curves are obtained

    本文以體積配箍率和軸壓比為主要控制參數，對不同配筋模式的6根高強混凝土壓彎構件進行了低周水平反復加載試驗，得到了箍筋約束混凝土的荷載?位移滯回曲線。
  8. In kinematics similarity test, test simulates specimens in earthquake action. by the hysteretic curve, anti - seismic property of t - shaped and l - shaped short - leg shear wall can be realized

    並且研究了在動荷載作用下混凝土等級、截面配筋率和墻肢截面高厚比等因素對短肢剪力墻抗震性能的影響。
  9. In static test, t - shaped and l - shaped specimens were respectively divided into four groups according to concrete strength grades, sectional height to thickness ratio, reinforcement ratio and ratio of axial compressive force to axial compressive ultimate capacity of section. how these factors affect the load - carrying and deformation of short - leg shear wall is known by analysis the result

    在擬靜力試驗中對t形和l形短肢剪力墻分別進行了四組試驗，通過對試驗結果的分析，揭示了混凝土等級、截面配筋率、軸壓比和墻肢截面高厚比等因素對短肢剪力墻承載力和變形的影響。
  10. Influences of load ratio, materials strength and ratio of reinforcement on seismic reliability of beams were analyzed

    研究了荷載比值、材料強度等級和配筋率對梁可靠度的影響。
  11. 3 ) a study is carried out to understand the changing rule of ultimate load and stiffness with the different reinforcement ratio of anti - punching shear bar. the increasing speed of the ultimate load is slower than that of the reinforcement ratio is indicated

    3 .對不同抗拔鋼筋配筋率的鋼筋混凝土承臺-鋼柱腳抗拔極限承載力和剛度變化規律進行了計算分析，發現了隨著承臺中抗拔鋼筋配筋率的提高，其承載力提高的比例逐步減小的規律。
  12. Problems are often occurred : cross - section of frame columns depends upon the limit of axial compressive ratio, the constructional reinforcement ratio becomes the ratio of longitudinal reinforcing steel bar of frame columns, such problems are not reasonable

    經常出現的情況是：框架柱的斷面由軸壓比限值確定，而框架柱的配筋由構造配筋率決定，這其中存在著不合理的地方。
  13. A simplified formula for the shear capacity of rc simply supported beam which strengthened with the cmmr is proposed in this paper. 3 、 the shear capacity of rc beam strengthened with cmmr is studied. though the test of fourteen simply supported reinforced concrete beams and five overhanging reinforced concrete beams with cmmr, it analyses the effects of shear - span ratio, web reinforcement ratio of cmmr, style of loading, preloading on strengthening, and compares them with rc beams using ordinary stirrup

    3 、根據本文進行了的14根混凝土簡支梁和5根混凝土伸臂梁的水泥復合砂漿鋼筋網抗剪加固試驗，分析了剪跨比、鋼筋網配筋率、加固形式以及持荷狀態等因數對整個構件極限抗剪承載力的影響，並與混凝土梁進行了比較。
  14. An experimental study on steel fiber reinforced concrete ( sfrc ) thick cap with four piles indicates that the factors affecting its ultimate loads are composed of its effective thickness, steel fiber volume ratio, concrete strength grade, shear span length, steel ratio and the form of reinforcement, in which the factor of the form of reinforcement affecting the ultimate loads of pile cap is distinct

    摘要鋼纖維混凝土四樁厚承臺的性能試驗研究結果表明，影響其極限荷載的因素主要有承臺有效厚度、鋼纖維體積率、混凝土基體強度等級、承臺的剪跨比、縱向鋼筋配筋率和配筋形式等，其中，配筋形式對鋼纖維混凝土厚承臺承載力的影響是很顯著的。
  15. The main work done in this paper is as follows : ( 1 ) simulate the temperature field of basement wall by ansys software, sum up the characteristics of the temperature field of basement wall, and analyze the influence of the types of the molding board, environmental change and cement content ; ( 2 ) the whole simulation analysis process of early - age concrete stress field is realized by sub - development of ansys, and cts - ansys software is developed with fortran ; ( 3 ) based on the cause of cracking, the influence of the thickness of the wall, length, bar arrangement, mix proportion, expanding agent, etc, on the wall stress due to concrete creep and temperature change is analyzed

    本文主要進行了以下幾個方面的研究： （ 1 ）利用ansys軟體，模擬了施工期地下室側墻溫度場，總結了地下室側墻溫度場分佈的特點，分析了模板類型、環境變化和水泥用量等對墻體溫度場的影響； （ 2 ）以大型通用有限元軟體ansys為平臺進行二次開發，運用visualfortran語言編寫了cts - ansys程序，實現了施工期混凝土徐變溫度應力的模擬計算； （ 3 ）從裂縫形成的原因出發，分析了地下室側墻厚度、長度、配筋率、配合比、膨脹劑等因素對墻體徐變溫度應力的影響。
  16. By taking axial compression ratio, local angle, stirrup space, the ratio of stirrup and etc. into consideration, the author studies the displacement ductility ratio for speical - shaped columns such as l shape, t shape and t shape

    摘要通過考慮不同軸壓比、不同加載角度和不同配筋率等情況，對異形柱位移延性比進行了研究。
  17. A program with c + + language was designed to calculate ultimate load of the reinforced concrete masonry shear wall structure. the reliability of the program was proved by comparing the program results with experimental results. ( 2 ) using the program, impact to the shear resistant of the ratio of grout for concrete and the ratio of height to section thickness and the horizontal reinforcement ratio was discussed

    （ 2 ）利用本文編制的程序，討論不同的高寬比、灌芯率和水平配筋率對配筋砌塊砌體剪力墻抗剪承載力的影響，並驗證了《砌體規范》 （ gb50003 - 2001 ）規定允許高寬比和允許配筋率范圍。
  18. In order to study the behavior of r. c. columns subjected to biaxially eccentric loading, the l - shaped column of three sets of steel ratios was calculated. according to the results calculated by the program ( asc ), the behavior of loading response was investigated

    為了研究異形截面柱的在雙向偏心受壓下的受力及變形規律，本文利用程序asc對三種不同配筋率下的l形柱進行了分析、比較，總結了異形截面柱的受力及變形規律。
  19. By modifying the level and vertical steel bars and adding bevel steel bars to the model structure, the paper compares the influencing factors of ratio of reinforcement and bevel steel bars to seismic properties, and pushes forward the methods to improve the seismic behaviors of the same kind

    ，通過改變模型結構水平與豎向配筋以及在墻板中增加斜向鋼筋等試驗參數，對比研究了配筋率和斜向鋼筋對其抗震性能的影響，提出了改進這類結構抗震性能的設計與構造建議。
  20. The main contents are followed below : ( 1 ) for the aim of knowing the characteristics of main factory building structure frame columns of large - scale thermal power plants, nine high strength concrete frame columns with high axial compression ratio and six slender ordinary strength concrete frame columns with high axial compression ratio were tested under low reversed cyclic horizontal loading for the very first time, and thus the influencing factors of normal section bearing capacity, such as concrete intensity grade, axial compressive ratio, slendemess ratio, the type of stirrups and stirrup ratio, etc, the anti seismic deformation capability of frame columns were acquired

    本文主要研究的內容有： （ 1 ）首次針對火電廠主廠房結構框架柱的特點，對9個高軸壓比高強混凝土框架柱和6個高軸壓比普通混凝土框架長柱進行了低周反復水平加載試驗，獲得混凝土等級、軸壓比、長細比、配箍形式及配筋率等對框架柱的抗彎及抗剪承載力、抗震變形能力的影響因素。
分享友人
分享到 Line

分享到臉書